What Cisco Catalyst switch feature can be used to defin…

What Cisco Catalyst switch feature can be used to define ports as trusted for DHCP server connections?

A.
DHCP snooping

B.
port security

C.
802.1x

D.
private VLANs

Explanation:
DHCP snooping is used to define ports as trusted for DHCP server connections. The purpose of DHCP snooping is to mitigate DHCP spoofing attacks. DHCP
spoofing is an attack that can be used to force user traffic through an attacking device. This is accomplished by an attacker responding to DHCP queries from
users. Eliminating the response from the correct DHCP server would make this more effective, but if the attacker’s response gets to the client first, the client will
accept it.
The DHCP response from the attacker will include a different gateway or DNS server address. If they define a different gateway, the user traffic will be forced to
travel through a device controlled by the attacker. This will allow the attacker to capture traffic and gain company information. If the attacker changes the DNS
server in the response, they can use their own DNS server to force traffic to selected hosts to go to a device they control. Again, this would allow the attacker to
capture traffic and gain information.
DHCP snooping can be used to determine what ports are able to send DHCP server packets, such as DHCPOFFER, DHCPACK, and DHCPNAK, from the
company DHCP server. DHCP snooping can also cache the MAC address to IP address mapping for clients receiving DHCP addresses from a valid DHCP server.
The three required steps to implement DHCP snooping are:
1. Enable DHCP snooping globally with the ip dhcp snooping command:
switch(config)# ip dhcp snooping
2. Enable DHCP snooping for a VLAN with the vlan parameter:
switch(config)# ip dhcp snooping vlan vlan #
(for example, ip dhcp snooping 10 12 specifies snooping on VLANs 10 and 12)
3. Define an interface as a trusted DHCP port with the trust parameter:
switch(config-if)# ip dhcp snooping trust
When specifying trusted ports, access ports on edge switches should be configured as untrusted, with the exception of any ports that may have company DHCP
severs connected. Only ports where DHCP traffic is expected should be trusted. Most certainly, ports in any area of the network where attacks have been detected
should be configured as untrusted.
Some additional parameters that can be used with the ip dhcp snooping command are:

switch(config)# ip dhcp snooping verify mac-address – this command enables DHCP MAC address verification.
switch(config)# ip dhcp snooping information option allow-untrusted – this command enables untrusted ports to accept incoming DHCP packets with option 82
information. DHCP option 82 is used to identify the location of a DHCP relay agent operating on a subnet remote to the DHCP server.
When DHCP snooping is enabled, no other relay agent-related commands are available. The disabled commands include:
ip dhcp relay information check global configuration
ip dhcp relay information policy global configuration
ip dhcp relay information trust-all global configuration
ip dhcp relay information option global configuration
ip dhcp relay information trusted interface configuration
Private VLANs are a method of protecting or isolating different devices on the same port and VLAN. A VLAN can be divided into private VLANs, where some
devices are able to access other devices and some are completely isolated from others. This was designed so service providers could keep customers on the same
port isolated from each other, even if the customers had the same Layer 3 networks.
Port security is a method of only permitting specified MAC addresses access to a switch port. This can be used to define what computer or device can be connected
to a port, but not to limit which ports can have DHCP servers connected to them.
802.1x is a method of determining authentication before permitting access to a switch port. This is useful in restricting who can connect to the switch, but it cannot
control which ports are permitted to have a DHCP server attached to it.
Objective:
Infrastructure Security
Sub-Objective:
Describe common access layer threat mitigation techniques

Home > Support > Product Support > Switches > Cisco Catalyst 4500 Series Switches > Configure > Configuration Guides > Chapter: Configuring DHCP Snooping
and IP Source Guard > Configuring DHCP Snooping on the Switch