Which command would you configure globally on a Cisco router that would allow you to view directly connected Cisco devices?
A.
cdp run
B.
enable cdp
C.
cdp enable
D.
run cdp
Which command would you configure globally on a Cisco r…
Which command would you configure globally on a Cisco router that would allow you to view directly connected Cisco devices?
New 200-125 Exam Questions and Answers Updated Recently (5/Apr/2017):
NEW QUESTION 640
If you are configuring syslog messages specifying `logging trap warning’, which log messages will the router send?
A. 0-4
B. 0-5
C. 0-6
D. 0-2
E. 0-1
Answer: A
Explanation:
0 — emergencies System is unusable
1 — alerts Immediate action is needed
2 — critical Critical conditions exist
3 — errors Error conditions exist
4 — warnings Warning conditions exist
5 — notification Normal, but significant, conditions exist
6 — informational Informational messages
7 — debugging Debugging messages
NEW QUESTION 641
Which command can you enter to configure an IPV6 floating static route?
A. Router(config)# ipv6 route FE80:0202::/32 serail 0/1 201
B. Router(config)# ipv6 route::/0 serail0/1
C. Router(config)# ipv6 route static resolve default
D. Router(config)# ipv6 route FE80:0202::/32 serail 0/1 1
Answer: A
NEW QUESTION 642
What is true about Ethernet? (Choose two.)
A. 802.2 Protocol
B. 802.3 Protocol
C. 10BaseT half duplex
D. CSMA/CD Stops transmitting when congestion occurs
E. CSMA/CA Stops transmitting when congestion occurs
Answer: BD
Explanation:
CSMA/CD — It uses a carrier sensing scheme in which a transmitting station detects collisions by sensing transmissions from other stations while transmitting a frame. When this collision condition is detected, the station stops transmitting that frame.
NEW QUESTION 643
What are types of IPv6 static routes? (Choose three.)
A. Recursive routes
B. Directly connected routes
C. Fully specified routes
D. Advertised routes
E. Virtual links
F. Redistributed routes
Answer: ABC
NEW QUESTION 644
How to configure RIPv2? (Choose two.)
A. Enable RIP
B. Connect RIP to WAN interface
C. Enable no auto-summary
D. Enable authentication
Answer: AC
NEW QUESTION 645
What is the status of port-channel if LACP is misconfigured?
A. Forwarding
B. Enabled
C. Disabled
D. errdisabled
Answer: D
NEW QUESTION 646
What is true about DTP? (Choose three.)
A. Layer 2 protocol
B. Layer 3 protocol
C. Proprietary protocol
D. enabled by default
E. disabled by default
Answer: ACD
NEW QUESTION 647
How to create a trunk port and allow VLAN 20? (Choose three.)
A. switchport trunk encapsulation dot1q
B. switchport mode trunk
C. switchport trunk allowed vlan 20
D. switchport trunk native vlan 20
Answer: ABC
NEW QUESTION 648
What 8-bit field exists in IP packet for QoS?
A. Tos Field
B. DSCP
C. IP Precedence
D. Cos
Answer: A
NEW QUESTION 649
……
NEW QUESTION 650
If you configure syslog messages without specifying the logging trap level, which log messages will the router send?
A. 0-4
B. 0-5
C. 0-6
D. 0-2
E. 0-1
Answer: C
NEW QUESTION 651
If a router has 3 hosts connected in one port and two other hosts connected in another port, how may broadcast domains are present on the router?
A. 5
B. 2
C. 3
D. 4
Answer: B
NEW QUESTION 652
What are three parts of an IPv6 global unicast address? (Choose three.)
A. an interface ID that is used to identify the local host on the network
B. an interface ID that is used to identify the local network for a particular host
C. a subnet ID that is used to identify networks inside of the local enterprise site
D. a global routing prefix that is used to identify the network portion of the address that has been provided by an ISP
E. a global routing prefix that is used to identify the portion of the network address provided by a local administrator
Answer: ACD
NEW QUESTION 653
What are the address that will show at the show ip route if we configure the above statements? (Choose three.)
A. 10.0.0.0
B. 10.4.3.0
C. 172.15.4.0
D. 172.15.0.0
E. 192.168.4.0
F. 192.168.0.0
Answer: ADE
NEW QUESTION 654
Which feature facilitate the tagging of a specific VLAN?
A. Routing
B. Hairpinning
C. Encapsulation
D. Switching
Answer: C
NEW QUESTION 655
What does split horizon prevent?
A. routing loops, link state
B. routing loops, distance vector
C. switching loops, STP
D. switching loops, VTP
Answer: B
NEW QUESTION 656
Which value to use in HSRP protocol election process ?
A. interface
B. virtual IP address
C. priority
D. router ID
Answer: C
NEW QUESTION 657
……
P.S. These New 200-125 Exam Questions Were Just Updated From The Real 200-125 Exam, You Can Get The Newest 200-125 Dumps In PDF And VCE From — http://www.passleader.com/200-125.html (718q VCE and PDF)
Good Luck!
Besides, part of that new 718Q 200-125 dumps are available here:
https://drive.google.com/open?id=0B-ob6L_QjGLpeHlmcExhU2FVY00
Best Regards!
thanks, mate, do you have the VCE also? Thanks. sorinT87 at gmail. thank you.
200-125 Exam Prep | Valid 200-125 Dumps | Latest 200-125 Questions
Subscribe Education Certifications Channel:
https://www.youtube.com/watch?v=7hG6JRVQbLo
New 200-125 Exam Questions and Answers Updated Recently (25/May/2017):
NEW QUESTION 716
Which IEEE mechanism is responsible for the authentication of devices when they attempt to connect to a local network?
A. 802.1x
B. 802.11
C. 802.2x
D. 802.3x
Answer: A
NEW QUESTION 717
If router R1 knows a static route to a destination network and then learns about the same destination network through a dynamic routing protocol, how does R1 respond?
A. It refuses to advertise the dynamic route to other neighbors
B. It sends a withdrawal signal to the neighboring router
C. It disables the routing protocol
D. It prefers the static route
Answer: D
NEW QUESTION 718
Which two statements about floating static routes are true? (Choose two.)
A. They are routes to the exact /32 destination address
B. They are used when a route to the destination network is missing
C. They have a higher administrative distance than the default static route administrative distance
D. They are used as back-up routes when the primary route goes down
E. They are dynamic routes that are learned from a server
Answer: CD
NEW QUESTION 719
When you enable PortFast on a switch port, the port immediately transitions to which state?
A. Blocking
B. Forwarding
C. Learning
D. Listening
Answer: B
NEW QUESTION 720
Refer to the exhibit. If R1 receives a packet destined to 172.16.1.1, to which IP address does it send the packet?
Image URL: passleader.org/wp-content/uploads/2017/05/passleader-200-125-dumps-7201.jpg
A. 192.168.14.4
B. 192.168.12.2
C. 192.168.13.3
D. 192.168.15.5
Answer: A
NEW QUESTION 721
What is the command to see assigned address in DHCP?
A. show ip DHCP statistic
B. show ip dhcp pool
C. show ip dhcp binding
D. show ip dhcp database
Answer: C
NEW QUESTION 722
Refer to the exhibit. You determine that Computer A cannot ping Computer Which reason for the problem is most likely true?
Image URL: passleader.org/wp-content/uploads/2017/05/passleader-200-125-dumps-7221.jpg
A. The Subnet mask for computer A is incorrect
B. The default gateway address for computer A is incorrect
C. The subnet mask for computer B is incorrect
D. The default gateway address for computer B is incorrect
Answer: A
NEW QUESTION 723
Which effect of the passive-interface command on R1 is true?
Image URL: passleader.org/wp-content/uploads/2017/05/passleader-200-125-dumps-7231.jpg
A. It prevents interface Fa0/0 from sending updates.
B. Interface Fa 0/0 operates in RIPv1 mode.
C. It removes the 172.16.0.0 network from all updates on all interfaces on R1.
D. It removes the 172.16.0.0 network from all updates on all interfaces on R1.
Answer: A
NEW QUESTION 724
Which three encapsulation layers in the OSI model are combined into the TCP/IP application layer? (Choose three.)
A. Session
B. transport
C. presentation
D. application
E. data-link
F. network
Answer: ACD
NEW QUESTION 725
When is the most appropriate time to escalate an issue that you troubleshooting?
A. When you lack the proper to resolve the issue
B. When a more urgent issue that requires your intervention is detected
C. When you have gathered all information about an issue
D. When you have been unable to resolve the issue after 30 min
Answer: C
NEW QUESTION 726
Which two command can you enter to display the current time sources statistics on devices? (Choose two.)
A. Show ntp associations.
B. Show clock details.
C. Show clock.
D. Show time.
E. Show ntp status.
Answer: AE
NEW QUESTION 727
Which two authentic methods are compatible with MLPPP on a serial Interface? (Choose two.)
A. PEAP
B. CHAP
C. TACACS+
D. PAP
E. LEAP
Answer: BD
NEW QUESTION 728
Which two statements about VTP are true? (Choose two.)
A. All switches must be configured with the same VTP domain name.
B. All switches must be configured to perform trunk negotiation.
C. All switches must be configured with a unique VTP domain name.
D. The VTP server must have the highest revision number in the domain.
E. All switches must use the same VTP version.
Answer: AD
NEW QUESTION 729
Refer to the exhibit. On R1 which routing protocol is in use on the route to 192.168.10.1?
A. RIP
B. OSPF
C. IGRP
D. EIGRP
Answer: D
NEW QUESTION 730
Which two options are the best reasons to use an IPV4 private IP space? (Choose two.)
A. to enable intra-enterprise communication
B. to implement NAT
C. to connect applications
D. to conserve global address space
E. to manage routing overhead
Answer: AD
NEW QUESTION 731
Which type does a port become when it receives the best BPDU on a bridge?
A. The designated port
B. The backup port
C. The alternate port
D. The root port
Answer: D
NEW QUESTION 732
Which value can you modify to configure a specific interface as the preferred forwarding interface?
A. The interface number
B. The port priority
C. The VLAN priority
D. The hello time
Answer: B
NEW QUESTION 733
Which statement about VLAN configuration is true?
A. The switch must be in VTP server or transparent mode before you can configure a VLAN
B. The switch must be in config-vlan mode before you configure an extended VLAN
C. Dynamic inter-VLAN routing is supported on VLAN2 through VLAN 4064
D. A switch in VTP transparent mode save the VLAN databases to the running configuration only
Answer: A
NEW QUESTION 734
In which two situations should you use out-of-band management?
A. when a network device fails to forward packets
B. when you require ROMMON access
C. when management applications need concurrent access to the device
D. when you require administrator access from multiple locations
E. when the control plane fails to respond
Answer: AB
NEW QUESTION 735
What happens when an 802.11a node broadcasts within the range of an 802.11g access point?
A. The access point transmits, but the node is unable to receive.
B. A connection occurs.
C. Both the node and the access point are unable to transmit.
D. The node transmits, but the access point is unable to receive.
Answer: D
NEW QUESTION 736
Which value indicate the distance from the ntp authoritative time source?
A. priority
B. location
C. layer
D. stratum
Answer: D
NEW QUESTION 737
Which NTP type designates a router without an external reefrence clock as an authoritative time source?
A. server
B. peer
C. master
D. client
Answer: C
NEW QUESTION 738
Which 3 feature are represented by A letter in AAA? (Choose three.)
A. authorization
B. accounting
C. authentication
D. accountability
E. accessibility
F. authority
Answer: ABC
NEW QUESTION 739
When you deploy multilink PPP on your network, where must you configure the group IP Address on each device?
A. in the global config
B. Under serial interface
C. Under the routing protocol
D. Under the multilink interface
Answer: D
NEW QUESTION 740
Host is able to ping a web server but it is not able to do HTTP request.
A. ACL blocking port 23
B. ACL blocking All ports
C. ACL blocking port 80
D. ACL blocking port 443
E. None of the above
Answer: C
NEW QUESTION 741
……
P.S. These New 200-125 Exam Questions Were Just Updated From The Real 200-125 Exam, You Can Get The Newest 200-125 Dumps In PDF And VCE From — http://www.passleader.com/200-125.html (750q VCE and PDF)
Good Luck!
Besides, part of the new 750Q 200-125 dumps are available here:
https://drive.google.com/open?id=0B-ob6L_QjGLpeHlmcExhU2FVY00
Best Regards!
New 200-125 Exam Questions and Answers Updated Recently (8/June/2017):
NEW QUESTION 754
Which value must the device send as its username when using CHAP to authenticate with the remote peer site id:17604704 over a PPP link?
A. The automatically generated user name
B. The local host name
C. The user name defined by the administrator
D. The host name of the remote device.
Answer: B
NEW QUESTION 755
What can you change to select switch as root bridge?
A. make lower priority
B. make higher priority
C. make lower path cost
D. make higher path cost
Answer: A
NEW QUESTION 756
Refer to exhibit. What Administrative distance has route to 192.168.10.1 ?
Image URL: passleader.org/wp-content/uploads/2017/06/passleader-200-125-dumps-7561.jpg
A. 1
B. 90
C. 110
D. 120
Answer: B
NEW QUESTION 757
Which statement about IPv6 link-local addresses is true ?
A. They must be configured on all IPv6 interface
B. They must be globally unique
C. They must be manually configured
D. They are advertised globally on the network
Answer: A
NEW QUESTION 758
Which configuration can be used with PAT to allow multiple inside address to be translated to a single outside address ?
A. Dynamic Routing
B. DNS
C. Preempt
D. overload
Answer: D
NEW QUESTION 759
Which two types of information are held in the MAC address table? (Choose two)
A. MAC address
B. soure IP address
C. destination IP address
D. Protocols
E. Port numbers
Answer: AE
NEW QUESTION 760
Which command can you enter to create a NAT pool of 6 addresses?
A. Router(config)#ip nat pool test 175.17.12.69 175.17.12.74 prefix-length 24
B. Router(config)#ip nat pool test 175.17.12.69 175.17.13.74 prefix-length 16
C. Router(config)#ip nat pool test 175.17.12.66 175.17.12.72 prefix-length 8
D. Router(config)#ip nat pool test 175.17.12.69 175.17.12.76 prefix-length 8
Answer: A
NEW QUESTION 761
……
P.S. These New 200-125 Exam Questions Were Just Updated From The Real 200-125 Exam, You Can Get The Newest 200-125 Dumps In PDF And VCE From — http://www.passleader.com/200-125.html (765q VCE and PDF)
Good Luck!
Besides, part of the new 765Q 200-125 dumps are available here:
https://drive.google.com/open?id=0B-ob6L_QjGLpeHlmcExhU2FVY00
Best Regards!
Can you send somebody valid dump for this exam please? [email protected]
Thanks in advance!
I have checked some reviews from CertBus 200-125 product page, seems good.
”
Perry
ChinaRating: 5.0
Hello, guys. i have passed the exam successfully in the morning,thanks you very much.
Jack
United StatesRating: 4.3
This dump is still valid. Just took my CCNA today and passed it. Every question i got on the test was in the dump.
Ravi
IndonesiaRating: 4.3
Valid study material! Go get it now!!!
zewpy
BrazilRating: 4.6
I used it,I passed. I found same questions..but it’s not the same orderl, be careful.
Donn
United StatesRating: 4.7
This dumps is still very valid, I have cleared the written exams passed today. Recommend.
Vadim
IndiaRating: 4.9
I passed the exam with perfect score. I’m so happy now. Thanks for my friends introduction, thanks for this dump.
Dean
MyanmarRating: 4.1
This dump is helpful and convenient, you can trust on it .Good luck to you.
Omar
NetherlandsRating: 4.2
Thanks for your help. I passed my exam yesterday with the full points! Great job.
”
Can someone share the CertBus 200-125 dumps? There are 930 Q&As in the CertBus dumps. https://www.certbus.com/200-125.html
Vendor: Cisco
Certifications: CCNA
Exam Name: CCNA Cisco Certified Network Associate CCNA (v3.0)
Exam Code: 200-125
Total Questions: 930 Q&As
QUESTION 1
Which technology supports the stateless assignment of IPv6 addresses?
A. DNS
B. DHCPv6
C. DHCP
D. autoconfiguration
Correct Answer: BD
Explanation
QUESTION 2
What are two requirements for an HSRP group? (Choose two.)
A. exactly one active router
B. one or more standby routers
C. one or more backup virtual routers
D. exactly one standby active router
E. exactly one backup virtual router
Correct Answer: AB
Explanation
QUESTION 3
After you configure the Loopback0 interface, which command can you enter to verify the status of the
interface and determine whether fast switching is enabled?
A. Router#show ip interface loopback 0
B. Router#show run
C. Router#show interface loopback 0
D. Router#show ip interface brief
Correct Answer: A
Explanation
QUESTION 4
Which command sequence can you enter to create VLAN 20 and assign it to an interface on a switch?
A. Switch(config)#vlan 20
Switch(config)#Interface gig x/y
Switch(config-if)#switchport access vlan 20
B. Switch(config)#Interface gig x/y
Switch(config-if)#vlan 20
Switch(config-vlan)#switchport access vlan 20
C. Switch(config)#vlan 20
Switch(config)#Interface vlan 20
Switch(config-if)#switchport trunk native vlan 20
D. Switch(config)#vlan 20
Switch(config)#Interface vlan 20
Switch(config-if)#switchport access vlan 20
E. Switch(config)#vlan 20
Switch(config)#Interface vlan 20
Switch(config-if)#switchport trunk allowed vlan 20
Correct Answer: A
Explanation
QUESTION 5
Which three commands can you use to set a router boot image? (Choose three.)
A. Router(config)# boot system flash c4500-p-mz.121-20.bin
B. Router(config)# boot system tftp c7300-js-mz.122-33.SB8a.bin
C. Router(config)#boot system rom c7301-advipservicesk9-mz.124-24.T4.bin
D. Router> boot flash:c180x-adventerprisek9-mz-124-6T.bin
E. Router(config)#boot flash:c180x-adventerprisek9-mz-124-6T.bin
F. Router(config)#boot bootldr bootflash:c4500-jk9s-mz.122-23f.bin
Correct Answer: ABC
Explanation
QUESTION 6
Which two statements about IPv6 and routing protocols are true? (Choose two.)
A. Link-local addresses are used to form routing adjacencies.
B. OSPFv3 was developed to support IPv6 routing.
C. EIGRP, OSPF, and BGP are the only routing protocols that support IPv6.
D. Loopback addresses are used to form routing adjacencies.
E. EIGRPv3 was developed to support IPv6 routing.
Correct Answer: AB
Explanation
QUESTION 7
If primary and secondary root switches with priority 16384 both experience catastrophic losses, which
tertiary switch can take over?
A. a switch with priority 20480
B. a switch with priority 8192
C. a switch with priority 4096
D. a switch with priority 12288
Correct Answer: A
Explanation
QUESTION 8
Which two statements about late collisions are true? (Choose two.)
A. They may indicate a duplex mismatch.
B. By definition, they occur after the 512th bit of the frame has been transmitted.
C. They indicate received frames that did not pass the FCS match.
D. They are frames that exceed 1518 bytes.
E. They occur when CRC errors and interference occur on the cable.
Correct Answer: AB
Explanation
QUESTION 9
Which command can you enter to set the default route for all traffic to an interface?
A. router(config)#ip route 0.0.0.0 0.0.0.0 GigabitEthernet0/1
B. router(config)#ip route 0.0.0.0 255.255.255.255 GigabitEthernet0/1
C. router(config-router)#default-information originate
D. router(config-router)#default-information originate always
Correct Answer: A
Explanation
QUESTION 10
Which two spanning-tree port states does RSTP combine to allow faster convergence? (Choose two.)
A. blocking
B. listening
C. learning
D. forwarding
E. discarding
Correct Answer: AB
Explanation
QUESTION 11
If a router has four interfaces and each interface is connected to four switches, how many broadcast
domains are present on the router?
A. 1
B. 2
C. 4
D. 8
Correct Answer: C
Explanation
QUESTION 12
Which command enables IPv6 forwarding on a Cisco router?
A. ipv6 local
B. ipv6 host
C. ipv6 unicast-routing
D. ipv6 neighbor
Correct Answer: C
Explanation
Certbus 2017 Real Cisco 200-125 CCNA Exam VCE and PDF Dumps for Free Download!
200-125 CCNA Exam PDF and VCE Dumps : 930Q&As Instant Download: https://www.certbus.com/200-125.html
[100% 200-125 Exam Pass Guaranteed or Money Refund!!]
New 200-125 Exam Questions and Answers Updated Recently (15/Aug/2017):
NEW QUESTION 795
While troubleshooting a connection problem on a computer, you determined that the computer can ping a specific web server but it cannot connect to TCP port 80 on that server. Which reason for the problem is most likely ture?
A. A VLAN number is incorrect
B. An ARP table entry is missing
C. A route is missing
D. An ACL is blocking the TCP port
Answer: D
NEW QUESTION 796
When troubleshooting Ethernet connectivity issues, how can you verify that an IP address is known to a router?
A. Check whether the IP address is in the routing table
B. Check whether an ACL is blocking the IP address
C. Check whether the IP address is in the CAM table
D. Check whether the IP address is in the ARP table
Answer: D
NEW QUESTION 797
Which two statements about IPv6 address 2002:ab10:beef::/48 are true? (Choose two.)
A. The embedded IPv4 address can be globally routed
B. It is used for an ISATAP tunnel
C. The embedded IPv4 address is an RFC 1918 address
D. The MAC address 20:02:b0:10:be:ef is embedded into the IPv6 address
E. It is used for a 6to4 tunnel
Answer: AE
NEW QUESTION 798
Which two steps must you perform on each device that is configured for IPv4 routing before you implement OSPFv3? (Choose two.)
A. configure an autonomous system number
B. configure a loopback interface
C. configure a router ID
D. enable IPv6 on an interface
E. enable IPv6 unicast routing
Answer: CE
NEW QUESTION 799
Which option is the main function of congestion management?
A. discarding excess traffic
B. queuing traffic based on priority
C. classifying traffic
D. providing long-term storage of buffered data
Answer: B
NEW QUESTION 800
Which command must you enter to enable OSPFV2 in an IPV4 network?
A. ip ospf hello-interval seconds
B. router ospfv2 process-id
C. router ospf value
D. router ospf process-id
Answer: D
NEW QUESTION 801
……
P.S. These New 200-125 Exam Questions Were Just Updated From The Real 200-125 Exam, You Can Get The Newest 200-125 Dumps In PDF And VCE From — https://www.passleader.com/200-125.html (808q VCE and PDF)
Good Luck!
Besides, part of the new 808Q 200-125 dumps are available here:
https://drive.google.com/open?id=0B-ob6L_QjGLpeHlmcExhU2FVY00
Best Regards!
Is it available for 1 month ? When this Dump will expire ?
Hi,
It is really confusing me. I can see 43 Questions at the same I can see some more question and answers shared by folks. Can we pass 200-125 exam if we read all these questions ?
Has anybody passed recently. ? Please advise.
I used it and passed my exam successfully yesterday. recommended dump exams!!
Thank you guys for sharing all those dumps.!!!!!
You used the 43 Q’s on here or the other dumps? thanks
Thanks for all the questions guys. They really helped a lot. I just took the ccna RS and came across many of the questions you presented. Really helped.
Hi. What’s up man. Please can your forward me your pdf files n question to this email. Kisitozion65yahoo.com.