What percentage of an I/O connection would you set the …

2017 New 200-601 exam questions updated today!

QUESTION 1
Which configuration enables an Industrial Ethernet switch to participate in PTP clock selection
and sets the priority value that would break the tie between switches with matching default criteria
to 50?
A. ptp mode boundary
ptp priority1 10
ptp priority2 50
B. ptp mode boundary
ptp priority1 50
ptp priority2 10
C. ptp mode e2etransparent
ptp priority1 50
ptp priority2 10
D. ptp mode e2etransparent
ptp priority1 10
ptp priority2 50
Answer: A

QUESTION 2
What are three Cisco best practices for running I/O control traffic in a wireless environment?
(Choose three)
A. 3200 packets per second and 20% bandwidth for HMI and maintenance traffic.
B. 2200 packets per second and 20% bandwidth for HMI and maintenance traffic
C. I/O control traffic can be run on 2.4 or 5 GHZ channels
D. I/O control traffic should be run on 5GHZ channels only
E. Standard I/O RPIs less than 20ms are not practical for wireless media because the maximum
latency and jitter become comparable or greater than the RPI
F. Standard I/O RPIs less than 10ms are not practical for wireless media because the maximum
latency and jitter become comparable or greater than the RPI
Answer: BDF

QUESTION 3
Which best describes the difference between 802.11n and 802.11ac?
A. 802.11ac offers more channels over more bands than 802.11n
B. 802.11ac MCS 1 is about twice as fast as 802.11n MCS1
C. 802.11ac offers more modulation schemes than 802.11n
D. 802.11ac 1SS MCS 9 is allowed over a 20, 40, 80 and 160 MHz channel, while 802.11n 1SS
MCS 9 is only allowed over a 20 or 40 MHz channel.
Answer: C

QUESTION 4
Refer to the exhbit. Which three elements would enable high availability and predictable
performance for a motion control application spread across two switches (with video and I/O
traffic)? (Choose three)
A. Configure QoS to give PTP traffic the highest priority
B. Fiber optic uplinks
C. Redundant uplinks
D. Configure QoS to give I/O traffic the highest priority
E. Copper uplinks
F. Interconnect the two switches
Answer: ABC

QUESTION 5
Which two actions are examples of network device hardening for Cisco Industrial Ethernet
Switches? (Choose two)
A. Disable unused services
B. Shutdown network ports which are not in use
C. Only allow administrative access using Telnet
D. Deploy IP67 versions of Cisco Industrial Ethernet Switches
E. Set the native VLAN on all trunk ports to VLAN 1
Answer: AB

QUESTION 6
You are called at home at 3am by an unskilled machine operator with a suspected network
related problem; the controller LEDs are all normal but the output module’s communications LED
is not on. The operator has verfied the cable is functional and correctly connected from the
communication module to the switch.
What is the next check that you ask the unskilled machine operator to make?
A. Log onto the switch using the console port and check that IGMP snooping is enabled
B. Open wireshark and check whether the controller is issuing a forward open instruction to the
device
C. Open the diagnostic faceplate on the HMI for the control panel switch and check that the relevant
ports are enabled and not in alarm
D. Open Studio 5000 and check the module status tab for the affected output module
Answer: C

QUESTION 7
Which three network mechanisms can be used for securely segmenting an industrial network?
(Choose three)
A. VLANs
B. OSPF
C. REP
D. VRFs
E. Firewalls
F. Spanning-tree
Answer: ADE

QUESTION 8
A cookie cutter machine requires 2 standard controllers and a safety controller. All of these
controllers and machine level I/O have been placed on VLAN 104. Both standard controllers must
monitor a photocell on this machine. Which IP address is used to transfer this status information?
A. 10.17.104.16
B. 192.168.1.16
C. 239.192.3.16
D. 239.192.254.16
Answer: C

QUESTION 9
Your controller has a high performance EtherNet/IP interface with port speed of >30,000 packets
per second and 80% spare capacity. A new PowerFlex 753 drive will be added to the system with
an RPI of 2ms and has been connected to a switch; you have been asked to set up the switch
port. You open the EDS file and see that the drive will support 16 CIP connections and has
transmit and receive capacity of 1,000 control packets per second.
What do you set as the storm control pps threshold limit for the port?
A. 16
B. 1,000
C. 2,500
D. 25,000
Answer: C
more new 200-601 exam questions from:https://www.braindump2go.com/200-601.html (this is a new 200-601 pdf and vce dumps 75q, updated on Aug 2, 2017)