Which symbol is required for globalized call routing?
A.
+
B.
*
C.
%
D.
/
E.
;
Which symbol is required for globalized call routing?
Which symbol is required for globalized call routing?
Leave a Reply
Which symbol is required for globalized call routing?
Which symbol is required for globalized call routing?
A.
+
B.
*
C.
%
D.
/
E.
;
2017 August 300-075 exam questions has been updated already!
Following is a part of new questions:
QUESTION 51
Which option is a benefit of implementing CFUR?
A. CFUR is designed to initiate TEHO to reduce toll charges.
B. CFUR can prevent phones from unregistering.
C. CFUR can reroute calls placed to a temporarily unregistered destination phone.
D. CFUR eliminates the need for COR on an ISR.
Answer: C
QUESTION 52
What is the standard Layer 3 DSCP media packet value that should be set for Cisco TelePresence endpoints?
A. CS3 (24)
B. EF (46)
C. AF41 (34)
D. CS4 (32)
Answer: D
QUESTION 53
You want to perform Media Gateway Control Protocol gateway maintenance. For this purpose, you disable Media Control Gateway Protocol gateway using the no mgcp command. After you perform the maintenance, you want to enable the Media Control Gateway Protocol gateway. Which command should you use?
A. enable mgcp
B. mgcp
C. mgcp enable
D. mgcp yes
E. activate mgcp
F. mgcp active
Answer: B
QUESTION 54
Which gateway does the Cisco Unified Communications Manager control all call activity?
A. SIP
B. MGCP
C. H.323
D. Media
Answer: B
QUESTION 55
Which action configures phones in site A to use G.711 to site B, but uses G.729 to site C?
A. Configure Cisco Unified Communications Manager regions.
B. Configure Cisco Unified Communications Manager locations.
C. Configure transcoder resources in Cisco Unified Communications Manager.
D. Configure a gatekeeper.
Answer: A
QUESTION 56
Refer to the exhibit. Which statement is true?
A. Endpoints can make calls to unknown IP addresses without the VCS querying any neighbors.
B. If the VCS receives a call to an unknown IP address, it queries its neighbors for the remote address and if permitted, it routes the call through the neighbor.
C. Endpoints that are registered directly to the VCS can call only an IP address of a system that is also registered directly to that VCS.
D. Dialing by IP address is not supported on VCS.
Answer: A
QUESTION 57
You want to avoid unnecessary interworking in Cisco TelePresence Video Communication Server, such as where a call between two H.323 endpoints is made over SIP, or vice versa.
Which setting is recommended?
A. H.323 – SIP interworking modE. Reject
B. H.323 – SIP interworking modE. On
C. H.323 – SIP interworking modE. Registered only
D. H.323 – SIP interworking modE. Off
E. H.323 – SIP interworking modE. Variable
Answer: C
QUESTION 58
Which commands are needed to configure Cisco Unified Communications Manager Express in SRST mode?
A. telephony-service and srst mode
B. telephony-service and moh
C. call-manager-fallback and srst mode
D. call-manager-fallback and voice-translation
Answer: A
QUESTION 59
Which component is needed to set up SAF CCD?
A. SAF-enabled H.323 intercluster (gatekeeper controlled) trunk
B. SAF forwarders on Cisco routers
C. Cisco Unified Communications cluster
D. SAF-enabled H.225 trunk
Answer: B
QUESTION 60
Which command is needed to utilize local dial peers on an MGCP-controlled ISR during an SRST failover?
A. ccm-manager fallback-mgcp
B. telephony-service
C. dialplan-pattern
D. isdn overlap-receiving
E. voice-translation-rule
Answer: A
More new 300-075 exam questions comes from:https://drive.google.com/drive/folders/0B75b5xYLjSSNOXRpM1hydUpDU3M?usp=sharing
get 2017 latest 300-075 PDF and 300-075 VCE from:
https://www.braindump2go.com/300-075.html
This is a braindump2go 390Q&As 300-075 Dumps 2017 new version, all new questions are shared there!
2018.Jan.9 New 300-075 Exam Questions and Answers：
QUESTION 189
Which of the following are two functions that ensure that the telephony capabilities stay operational in the remote location Cisco Unified SRST router? (Choose two)
A. Automatically detecting a failure in the network.
B. Initiating a process to provide call-processing backup redundancy.
C. Notifying the administrator of an issue for manual intervention.
D. Proactively repairing issues in the voice network.
Answer: AB
QUESTION 190
Which three of the following are steps in configuring MGCP Fallback and Cisco Unified SRST? (Choose three)
A. Define the SRST reference for phones in the Device Pool configuration
B. Enable and configure the MGCP fallback and Cisco Unified SRST features on the IOS gateways.
C. Implement a simplified SRST dial plan on the remote-site-gateways to ensure connectivity for remote-site phones in SRST mode.
D. Enable SIP trunking between both remote and hub sites to provide mesh coverage.
E. Define the SRST reference in the configuration on the IP Phones.
F. Enable and configure the MGCP fallback on the IOS gateway but not Cisco Unified SRST since it is enabled automatically.
Answer: ABC
QUESTION 191
Which method can be used to address variable-length dial plans?
A. Overlap sending and receiving.
B. Add a prefix for all calls that are longer than 10-digits long
C. Use nested translation patterns to eliminate inter-digit timeout
D. Use the @macro on the route pattern
E. Use MGCP gateways, which support variable-length dial plans
Answer: A
Explanation:
If the dial plan contains overlapping patterns, Cisco Unified Communications Manager does not route the call until the interdigit timer expires (even if it is possible to dial a sequence of digits to choose a current match). Check this check box to interrupt interdigit timing when Cisco Unified Communications Manager must route a call immediately. By default, the Urgent Priority check box displays as checked. Unless your dial plan contains overlapping patterns or variable length patterns that contain!, Cisco recommends that you do not uncheck the check box.
QUESTION 192
Refer to the exhibit. Which trunks would be most suitable for Connection Y?
A. an H.225 trunk (gatekeeper-controlled)
B. intercluster trunk (gatekeeper-controlled)
C. a SIP trunk on the U.S. cluster and an intercluster trunk on the remote cluster
D. intercluster trunk (nongatekeeper-controlled)
E. No extra connections are required. As long as IP connectivity exists, you need only configure a route pattern for each site. The Cisco Unified Communications Manager will automatically forward the calls over the WAN if the destination directory number is not registered locally.
Answer: D
QUESTION 193
Which two features require or may require configuring a SIP trunk? (Choose two.)
A. SIP gateway
B. Call Control Discovery between a Cisco Unified Communications Manager and Cisco Unified Communications Manager Express
C. Cisco Device Mobility
D. Cisco Unified Mobility
E. registering a SIP phone
Answer: AB
Explanation:
All protocols require that either a signaling interface (trunk) or a gateway be created to accept and originate calls. Device mobility allows Cisco Unified Communications Manager to determine whether the phone is at its home location or at a roaming location. Cisco Unified Mobility gives users the ability to redirect incoming IP calls from Cisco Unified Communications Manager to different designated phones, such as cellular phones.
QUESTION 194
A Cisco 3825 needs to be added in Cisco Unified Communications Manager as an H.323 gateway. What should the gateway type be?
A. H.323 gateway
B. Cisco 3825
C. Cisco 3800 series router. The specific model will be selected after the Cisco 3800 is selected.
D. The gateway can be added either as an H.323 gateway or Cisco 3800 series router.
E. The gateway can be added either as an H.323 gateway or Cisco 3825 series router.
Answer: A
QUESTION 67
When an incoming PSTN call arrives at an MGCP gateway, how does the calling number get normalized to a global E.164 number with the + prefix in Cisco Unified Communications Manager?
A. Normalization is done using translation patterns.
B. Normalization is done using route patterns.
C. Normalization is done using the gateway incoming called party prefixes based on number type.
D. Normalization is done using the gateway incoming calling party prefixes based on number type.
E. Normalization is achieved by local route group that is assigned to the MGCP gateway.
Answer: D
Explanation:
Configuring calling party normalization alleviates issues with toll bypass where the call is routed to multiple locations over the IP WAN. In addition, it allows Cisco Unified Communications Manager to distinguish the origin of the call to globalize or localize the calling party number for the phone user.
QUESTION 195
When an incoming PSTN call arrives at an MGCP gateway, how does the called number get normalized to an internal directory number in Cisco Unified Communications Manager?
A. Normalization is done by configuring the significant digits for inbound calls on the MGCP gateway.
B. Normalization is done using route patterns.
C. Normalization is done using the gateway incoming called party prefixes based on number type.
D. Normalization is done using the gateway incoming calling party prefixes based on number type.
E. Normalization is achieved by local route group that is assigned to the MGCP gateway.
Answer: A
QUESTION 196
Which process can localize a global E.164 with + prefix calling numbers for inbound calls to an IP phone so that users see the calling number in a local format?
A. Calling number localization is done using translation patterns.
B. Calling number localization is done using route patterns.
C. Calling number localization is done by configuring a calling party transformation CSS at the phone.
D. Calling number localization is done by configuring a calling party transformation CSS at the gateway.
E. Calling number localization is done by configuring the phone directory number in a localized format.
Answer: C