Refer to the exhibit. On the basis of the output, what two conclusions can be reached?
(Choose two.)
A.
The default administrative distance has been changed.
B.
IS-IS is not enabled.
C.
Three physical interfaces are taking part in integrated IS-IS.
D.
IS-IS is not redistributing any other routing protocols.
E.
There are two neighboring routers sending IS-IS routing information.
F.
Address summarization is configured.
Explanation:
Verifying IS-IS Configuration
To verify the IS-IS configuration and IP functionality of an Integrated IS-IS network, use the
following commands; these commands can also be useful for troubleshooting problems with
the IS- IS network:
• show ip protocols— Displays the active IP routing protocols, the interfaces on which
they are active, and the networks for which they are routing.
• show ip route [address [mask]] | [protocol [process-id]]— Displays the IP routing
table. You can specify the details for a particular route or a list of all routes in the routing
table from a particular routing protocol process.
Example 6-3 is sample output from the show ip protocols command that displays information
about IP routing being done by Integrated IS-IS. IS-IS is running, it is not redistributing any
other protocols, and address summarization has not been configured. Example 6-3 also
shows that interfaces FastEthernet 0/0, Loopback 0, and Serial 0/0/1 are taking part in
Integrated IS-IS, that there are two sources of routing information (the neighboring routers),
and that the administrative distance of Integrated IS-IS is 115.
Example 6-3, “show ip protocols” Command to Examine IS-IS:
R2#show ip protocolsRouting Protocol is “isis”
Invalid after 0 seconds, hold down 0, flushed after 0
Outgoing update filter list for all interfaces is not set
Incoming update filter list for all interfaces is not set
Redistributing: isis
Address Summarization:
None
Maximum path: 4
Routing for Networks:
FastEthernet0/0
Loopback0
Serial0/0/1
Routing Information Sources:
Gateway Distance Last Update
10.10.10.10 115 00:00:02
10.30.30.30 115 00:00:03
Distance: (default is 115)R2# Authorized Self-Study Guide Building Scalable Cisco Internetworks (BSCI), Third
Edition
http://safari.ibmpressbooks.com/1587052237/ch06lev1sec4
I am wondering, regarding cisco webpage IS-IS is not scope of this exam???
https://learningnetwork.cisco.com/community/certifications/ccnp/route_v2/exam-topics
(4/July/2017 Updated) New 300-101 Exam Questions:
NEW QUESTION 378
What is used in EIGRP metric calculation?
A. maximum delay
B. minimum delay
C. average delay
D. minimum interface bandwidth
Answer: D
NEW QUESTION 379
What show command is used here?
TCB Local Address Foreign Address (state)
6523A4FC 10.1.25.3.11000 10.1.25.3.23 ESTAB
65239A84 10.1.25.3.23 10.1.25.3.11000 ESTAB
653FCBBC *.1723 *.* LISTEN
A. show tcp brief
B. show tcp brief all
C. show tcp brief numeric
D. show tcp brief ip
Answer: ……
NEW QUESTION 380
You need the IP address of the devices with which the router has established an adjacency. Also, the retransmit interval and the queue counts for the adjacent routers need to be checked. What command will display the required information?
A. show ip eigrp adjacency
B. show ip eigrp topology
C. show ip eigrp interfaces
D. show ip eigrp neighbor
Answer: D
NEW QUESTION 381
You get a call from a network administrator who tells you that he typed the following into his router:
Router(config)#router ospf 1
Router(config-router)#network 10.0.0.0 255.0.0.0 area 0
He tells you he still can’t see any routes in the routing table. What configuration error did the administrator make?
A. The wildcard mask is incorrect
B. The OSPF area is wrong
C. The OSPF process ID is incorrect
D. The AS configuration is wrong
Answer: ……
NEW QUESTION 382
If routers in a single area are configured with the same priority value, what value does a router use for the OSPF Router ID in the absence of a loopback interface?
A. The lowest IP address of any physical interface
B. The highest IP address of any physical interface
C. The lowest IP address of any logical interface
D. The highest IP address of any logical interface
Answer: B
NEW QUESTION 383
Where are EIGRP successor routes stored?
D. In the routing table and the topology table
NEW QUESTION 384
Which location is traffic from IP SLAs?
A. core edge
B. access edge
C. WAN edge
D. Distribution edge
E. User edge
Answer: C
NEW QUESTION 385
Which option is invalid redistribute from EIGRP into OSPF?
A. ACL
B. tag
C. metric
D. route map
Answer: A
NEW QUESTION 386
……
Get The Newest 300-101 Dumps In PDF And VCE From — http://www.passleader.com/300-101.html (403q VCE and PDF)
Good Luck!
What’s more, part of that new 403Q 300-101 dumps FYI:
https://drive.google.com/open?id=0B-ob6L_QjGLpZEE0S2YxR3ZMUWs
Best Regards!
New 300-101 Exam Questions and Answers (2/Nov/2017 Updated):
NEW QUESTION 460
What is the minimum privilege level to enter all commands in usermode?
A. Level14
B. Level0
C. Level1
D. Level15
Answer: C
NEW QUESTION 461
Which two statements about password-protecting device access are true? (Choose two)
A. The more system:running-config command displays encrypted passwords in clear text.
B. The service password-encryption command forces a remote device to encrypt the password.
C. A network administrator can recover an encrypted password.
D. The privilege level command controls the commands a specific user can execute.
E. The password can be encrypted in the running configuration.
Answer: DE
NEW QUESTION 462
Frame Relay LMI autosense. Which statements are true? (Choose two.)
A. Line should be up and protocol should be down.
B. Protocol must be up.
C. It only works on DTEs.
D. It only works on DCEs.
Answer: AC
NEW QUESTION 463
Which two protocols can cause TCP starvation? (Choose two.)
A. TFTP
B. SNMP
C. SMTP
D. HTTPS
E. FTP
Answer: AB
NEW QUESTION 464
Refer to the exhibit. How can you configure a second export destination for IP address 192.168.10.1?
configure terminal
ip flow-export destination 192.168.10.1 9991
ip flow-export version 9
A. specify a different TCP port
B. specify a different UDP port
C. specify a VRF
D. configure a version 5 flow-export to the same destination
E. specify a different flow ID
Answer: C
NEW QUESTION 465
Which value does Frame Relay use to identify a connection between a DTE and DCE?
A. DLCI
B. IP address
C. MAC address
D. VLAN ID
Answer: A
NEW QUESTION 466
Which two options are limitations of Stateful NAT64? (Choose two.)
A. it is unable to route VRF traffic
B. it is unable to route multicast traffic
C. it supports FTP traffic only with an ALG
D. it supports DNS64 only
E. layer 4 supports TCP only
Answer: AB
NEW QUESTION 467
If you want to migrate an IS-IS network to another routing protocol with ……? (Choose two.)
A. UDP
B. Internal BGP
C. TCP/IP
D. EIGRP
E. OSPF
F. RIP
Answer: DE
NEW QUESTION 468
IP CEF load-sharing options ……? (Choose three.)
A. Tunnel
B. Universal
C. Include-ports
D. Source
E. Destination
Answer: ABC
NEW QUESTION 469
……
P.S. You Can Get The Newest 300-101 Dumps In PDF And VCE From — https://www.passleader.com/300-101.html (489q VCE and PDF)
Good Luck!
By the way, a lot of that new 489Q 300-101 dumps are available here:
https://drive.google.com/open?id=0B-ob6L_QjGLpZEE0S2YxR3ZMUWs
Best Regards!