Refer to the exhibit. Router RTA is the hub router for routers RTB and RTC. The Frame
Relay network is configured with EIGRP, and the entire network is in autonomous system 1.
However, router RTB and RTC are not receiving each other’s routes. What is the solution?
A.
Check and change the access lists on router RTA.
B.
Configure the auto summary command under router eigrp 1 on router RTA.
C.
Configure subinterfaces on the spoke routers and assign different IP address subnets for
each subinterface.
D.
Issue the no ip split horizon command on router RTA.
E.
Issue the no ip split horizon eigrp 1 command on router RTA.
F.
Configure a distribute list on router RTA that allows it to advertise all routes to the spoke
routers.
Explanation:
Split horizon controls the sending of EIGRP update and query packets. When split horizon is
enabled on an interface, these packets are not sent for destinations for which this interface is
the next hop. This reduces the possibility of routing loops.
By default, split horizon is enabled on all interfaces.Split horizon blocks route information from being advertised by a router out of any interface
from which that information originated. This behavior usually optimizes communications
among multiple routing devices, particularly when links are broken. However, with
nonbroadcast networks (such as Frame Relay and SMDS), situations can arise for which
this behavior is less than ideal. For these situations, you may want to disable split horizon.
In this example, routes received by RTB and RTC are not being sent back out the same
serial interface on RTA, so they are not receiving each other’s routes. Disabling Split
horizons on interface S0/0 on RTA will fix this issue.
2017/7/18 300-101 Exam Questions has been updated(I need someone else to help me check answers):
QUESTION 378
What is used in EIGRP metric calculation?
A. maximum delay
B. minimum delay
C. average delay
D. minimum interface bandwidth
Answer: D
QUESTION 379
What show command is used here?
TCB Local Address Foreign Address (state)
6523A4FC 10.1.25.3.11000 10.1.25.3.23 ESTAB
65239A84 10.1.25.3.23 10.1.25.3.11000 ESTAB
653FCBBC *.1723 *.* LISTEN
A. show tcp brief
B. show tcp brief all
C. show tcp brief numeric
D. show tcp brief ip
Answer: C
QUESTION 380
You need the IP address of the devices with which the router has established an adjacency.
Also, the retransmit interval and the queue counts for the adjacent routers need to be checked.
What command will display the required information?
A. show ip eigrp adjacency
B. show ip eigrp topology
C. show ip eigrp interfaces
D. show ip eigrp neighbor
Answer: D
QUESTION 381
You get a call from a network administrator who tells you that he typed the following into his router:
Router(config)#router ospf 1
Router(config-router)#network 10.0.0.0 255.0.0.0 area 0
He tells you he still can’t see any routes in the routing table.
What configuration error did the administrator make?
A. The wildcard mask is incorrect
B. The OSPF area is wrong
C. The OSPF process ID is incorrect
D. The AS configuration is wrong
Answer: A
QUESTION 382
If routers in a single area are configured with the same priority value, what value does a router use for the OSPF Router ID in the absence of a loopback interface?
A. The lowest IP address of any physical interface
B. The highest IP address of any physical interface
C. The lowest IP address of any logical interface
D. The highest IP address of any logical interface
Answer: B
QUESTION 383
Where are EIGRP successor routes stored?
A. In the routing table only
B. In the neighbor table only
C. In the topology table only
D. In the routing table and the topology table
E. In the routing table and the neighbor table
Answer: D
QUESTION 384
Which location is traffic from IP SLAs?
A. core edge
B. access edge
C. WAN edge
D. Distribution edge
E. User edge
Answer: C
QUESTION 385
Option invalid redistribute from EIGRP into OSPF
A. ACL
B. tag
C. metric
D. route map
Answer: A
I find these new questions from a guy’s a pdf share:
https://drive.google.com/drive/folders/0B75b5xYLjSSNUlpIeEc2YV9vRDg?usp=sharing
Hey, let’s share new questions we got!
2017/November New 300-101 Exam Questions Free Updated Today!
QUESTION 463
Which two protocols can cause TCP starvation? (Choose two)
A. TFTP
B. SNMP
C. SMTP
D. HTTPS
E. FTP
Answer: AB
QUESTION 464
Refer to the exhibit. How can you configure a second export destination for IP address 192.168.10.1?
A. specify a different TCP port
B. specify a different UDP port
C. specify a VRF
D. configure a version 5 flow-export to the same destination
E. specify a different flow ID
Answer: C
QUESTION 465
Which value does Frame Relay use to identify a connection between a DTE and DCE?
A. DLCI
B. IP address
C. MAC address
D. VLAN ID
Answer: A
QUESTION 466
Which two options are limitations of Stateful NAT64? (Choose two)
A. it is unable to route VRF traffic
B. it is unable to route multicast traffic
C. it supports FTP traffic only with an ALG
D. it supports DNS64 only
E. layer 4 supports TCP only
Answer: AB
QUESTION 467
If you want to migrate an IS-IS network to another routing protocol with…..? (Choose two)
A. UDP
B. internal BGP
C. TCP/IP
D. EIGRP
E. OSPF
F. RIP
Answer: DE
QUESTION 468
IP CEF load-sharing options (Choose three)
A. Tunnel
B. Universal
C. Include-ports
D. Source
E. Destination
Answer: ABC
QUESTION 469
What is the minimum privilege level to enter all commands in usermode?
A. Level14
B. Level0
C. Level1
D. Level15
Answer: C
QUESTION 470
Which two statements about password-protecting device access are true? (Choose two)
A. The more system:running-config command displays encrypted passwords in clear text
B. The service password-encryption command forces a remote device to encrypt the password
C. A network administrator can recover an encrypted password
D. The privilege level command controls the commands a specific user can execute
E. The password can be encrypted in the running configuration
Answer: DE
QUESTION 471
Frame Relay LMI autosense. What is is true? (Choose two)
A. Line should be up and protocol should be down
B. Protocol must be up
C. It only works on DTEs
D. It only works on DCEs
Answer: AC
More New 300-101 Real Exam Questions: https://www.braindump2go.com/300-101.html (489Q PDF and VCE Dumps)
2018 Jan New Cisco 300-101 Exam Questions:
QUESTION 165
A network engineer is considering enabling load balancing with EIGRP.
Which consideration should be analyzed?
A. EIGRP allows a maximum of four paths across for load balancing traffic.
B. By default, EIGRP uses a default variance of 2 for load balancing.
C. EIGRP unequal path load balancing can result in routing loops.
D. By default, EIGRP performs equal cost load balancing at least across four equal cost paths.
Answer: D
QUESTION 166
The OSPF database of a router shows LSA types 1, 2, 3, and 7 only.
Which type of area is this router connected to?
A. stub area
B. totally stubby area
C. backbone area
D. not-so-stubby area
Answer: D
QUESTION 167
An engineer is configuring a GRE tunnel interface in the default mode. The engineer has assigned an IPv4 address on the tunnel and sourced the tunnel from an Ethernet interface. Which option also is required on the tunnel interface before it is operational?
A. tunnel destination address
B. keepalives
C. IPv6 address
D. tunnel protection
Answer: A
QUESTION 168
Which protocol is used in a DMVPN network to map physical IP addresses to logical IP addresses?
A. BGP
B. LLDP
C. EIGRP
D. NHRP
Answer: D
QUESTION 169
Which two routing protocols are supported by Easy Virtual Network? (Choose two.)
A. RIPv2
B. OSPFv2
C. BGP
D. EIGRP
E. IS-IS
Answer: BD
QUESTION 170
Which statement is true?
A. RADIUS uses TCP, and TACACS+ uses UDP.
B. RADIUS encrypts the entire body of the packet.
C. TACACS+ encrypts only the password portion of a packet.
D. TACACS+ separates authentication and authorization.
Answer: D
QUESTION 171
Which two statements about AAA implementation in a Cisco router are true? (Choose two.)
A. RADIUS is more flexible than TACACS+ in router management.
B. RADIUS and TACACS+ allow accounting of commands.
C. RADIUS and TACACS+ encrypt the entire body of the packet.
D. RADIUS and TACACS+ are client/server AAA protocols.
E. Neither RADIUS nor TACACS+ allow for accounting of commands.
Answer: BD
QUESTION 172
Which option is invalid when configuring Unicast Reverse Path Forwarding?
A. allow self ping to router
B. allow default route
C. allow based on ACL match
D. source reachable via both
Answer: D
2018 New Cisco 300-101 Exam Dumps with PDF and VCE Full Version: https://www.braindump2go.com/300-101.html