Refer to the exhibit. EIGRP is configured on all routers in the network. On a basis of the
show ip eigrp topology output provided, what conclusion can be derived?
A.
Router R1 is waiting for a reply from the neighbor 10.1.2.1 to the hello message sent out
inquiring for a second successor to network 10.6.1.0/24.
B.
Router R1 can send traffic destined for network 10.6.1.0/24 out of interface
FastEthernet0/0.
C.
Router R1 is waiting for a reply from the neighbor 10.1.2.1 to the hello message sent out
before it declares the neighbor unreachable.
D.
Router R1 is waiting for a reply from the neighbor 10.1.2.1 in response to the query sent
out about network 10.6.1.0/24.
Explanation:
The “show ip eigrp topology” command lists all routes that EIGRP is aware of and shows
whether EIGRP is actively processing information on that route. Under most normal
conditions, the routes should all be in a passive state and no EIGRP process are running for
that route. If the routes are active, this could indicate the dreaded stuck in active, or SIA,
state.
The fields to note in this output are as follows:
• P— Passive; no EIGRP computation is being performed. This is the ideal state.
• A— Active; EIGRP computations are “actively” being performed for this destination.
Routes constantly appearing in an active state indicate a neighbor or query problem. Both
are symptoms of the SIA problem.
• U— Update; an update packet was sent to this destination.• Q— Query; a query packet was sent to this destination.
• R— Reply; a reply packet was sent to this destination.
• Route information— IP address of the route or network, its subnet mask, and the
successor, or next hop to that network, or the feasible successor.
Passed 300-101 Exam Today in California. 16 new questions but not a big deal. Easy! Studied this file, some questions’ answers are wrong! And got 12 new questions from the 371Q&As 300-101 pdf and vce dumps: https://www.braindump2go.com/300-101.html , this file is 86% valid enough for exam passing, can have a try. share some questions i got in my real test:
QUESTION 161
On which two types of interface is Frame Relay switching supported? (Choose two.)
A. serial interfaces
B. Ethernet interfaces
C. fiber interfaces
D. ISDN interfaces
E. auxiliary interfaces
Answer: AD
QUESTION 162
In IPv6, SLAAC provides the ability to address a host based on a network prefix that is advertised from a local network router. How is the prefix advertised?
A. routing table
B. router advertisements
C. routing protocol
D. routing type
Answer: B
QUESTION 163
Refer to the exhibit. Which option prevents routing updates from being sent to the access layer switches?
A. DWS1(config-router)# passive-interface default
DWS2(config-router)# passive-interface default
B. ALS1(config-router)# passive-interface default
ALS2(config-router)# passive-interface default
C. DWS1(config-router)# passive-interface gi1/1
DWS1(config-router)# passive-interface gi1/2
DWS2(config-router)# passive-interface gi1/1
DWS2(config-router)# passive-interface gi1/2
D. ALS1(config-router)# passive-interface gi0/1
ALS1(config-router)# passive-interface gi0/2
ALS2(config-router)# passive-interface gi0/1
ALS2(config-router)# passive-interface gi0/2
Answer: C
QUESTION 164
Refer to the exhibit. Which option prevents routing updates from being sent to the DHCP router, while still allowing routing update messages to flow to the Internet router and the distribution switches?
A. DHCP(config-router)# passive-interface default
DHCP(config-router)# no passive-interface Gi1/0
Internet(config-router)# passive-interface Gi0/1
Internet (config-router)# passive-interface Gi0/2
B. Core(config-router)# passive-interface Gi0/0
Core(config-router)# passive-interface Gi3/1
Core(config-router)# passive-interface Gi3/2
DHCP(config-router)# no passive-interface Gi1/0
C. Core(config-router)# passive-interface default
Core(config-router)# no passive-interface Gi0/0
Core(config-router)# no passive-interface Gi3/1
Core(config-router)# no passive-interface Gi3/2
D. Internet(config-router)# passive-interface default
Core(config-router)# passive-interface default
DSW1(config-router)# passive-interface default
DSW2(config-router)# passive-interface default
Answer: C
QUESTION 165
A network engineer is considering enabling load balancing with EIGRP.
Which consideration should be analyzed?
A. EIGRP allows a maximum of four paths across for load balancing traffic.
B. By default, EIGRP uses a default variance of 2 for load balancing.
C. EIGRP unequal path load balancing can result in routing loops.
D. By default, EIGRP performs equal cost load balancing at least across four equal cost paths.
Answer: D
QUESTION 166
The OSPF database of a router shows LSA types 1, 2, 3, and 7 only.
Which type of area is this router connected to?
A. stub area
B. totally stubby area
C. backbone area
D. not-so-stubby area
Answer: D
QUESTION 167
An engineer is configuring a GRE tunnel interface in the default mode. The engineer has assigned an IPv4 address on the tunnel and sourced the tunnel from an Ethernet interface. Which option also is required on the tunnel interface before it is operational?
A. tunnel destination address
B. keepalives
C. IPv6 address
D. tunnel protection
Answer: A
QUESTION 168
Which protocol is used in a DMVPN network to map physical IP addresses to logical IP addresses?
A. BGP
B. LLDP
C. EIGRP
D. NHRP
Answer: D
QUESTION 169
Which two routing protocols are supported by Easy Virtual Network? (Choose two.)
A. RIPv2
B. OSPFv2
C. BGP
D. EIGRP
E. IS-IS
Answer: BD
QUESTION 170
Which statement is true?
A. RADIUS uses TCP, and TACACS+ uses UDP.
B. RADIUS encrypts the entire body of the packet.
C. TACACS+ encrypts only the password portion of a packet.
D. TACACS+ separates authentication and authorization.
Answer: D
Wish you also can pass successfully!