Which two statements about the EIGRP DUAL process are correct?

Which two statements about the EIGRP DUAL process are correct? (Choose two.) Select 2
response(s).

Which two statements about the EIGRP DUAL process are correct? (Choose two.) Select 2
response(s).

A.
An EIGRP route will go active if there are no successors or feasible successors in the
EIGRP topology table.

B.
An EIGRP route will go passive if there are no successors in the EIGRP topology table.

C.
DUAL will trigger an EIGRP query process while placing the flapping routes in the
holddown state.

D.
A feasible successor in the EIGRP topology table can become the successor only after all
the query requests have been replied to.

E.
The stuck in active state is caused when the wait for the query replies have timed out.

F.
EIGRP queries are sent during the loading state in the EIGRP neighbor establishment
process.

Show Hint

Leave a Reply 1

Your email address will not be published. Required fields are marked *

Caffrey

Caffrey

New 300-101 Questions and Answers:

QUESTION 296
Which type of access list allows granular session filtering for upper-level protocols?

A. content-based access lists
B. context-based access lists
C. reglexive access lists
D. extended access lists

Answer: D

QUESTION 297
Which three configuration parameters can a DHCPV6 pool contain? (Choose three.)

A. domain search list
B. router IP
C. default gateway
D. prefix delegation
E. DNS servers
F. subnet mask

Answer: DEF

QUESTION 298
Which statement about local policy routing is true?

A. It is used to policy route packets that are generated by the device.
B. It requires all packets to be packet switched.
C. It is used to policy route packets that pass through the device.
D. It requires all packets to be CEF switched.
E. It supports IPv4 packets only.
F. It requires an ip address or access list as the matching criteria.

Answer: A

QUESTION 299
Which SNMP verification command shows the encryption and authentication protocols that are used in SNMPV3?

A. show snmp group
B. show snmp user
C. show snmp
D. show snmp view

Answer: B

QUESTION 300
Which type of information is displayed when a network engineer executes the show track 1 command on the router?

A. information about tracking list 1.
B. time to next poll for track object 1.
C. information about the IP route track table.
D. tracking information statistics.

Answer: A

QUESTION 301
Which command sequence can you enter on a router to configure Unicast Reverse Path Forwarding in loose mode?

A. interface GigabitEthernet0/0
ip verigy unicast source reachable-via all
B. interface GigabitEthernet0/0
ip verigy unicast source reachable-via loose
C. interface GigabitEthernet0/0
ip verigy unicast source reachable-via any
D. interface GigabitEthernet0/0
ip verigy unicast source reachable-via rx

Answer: C

QUESTION 302
Where can NetFlow export data for long term storage and analysis?

A. syslog
B. collector
C. another network device
D. flat file

Answer: B

QUESTION 303
Which option is the first task that a device that is configured with NAT64 performs when it receives an incoming IPv6 packet that matches the stateful NAT64 prefix?

A. It translates the IPv6 header into an IPv4 header.
B. It checks the IPv6 packet against the NAT64 stateful prefix.
C. It translates the IPv6 source address to an IPv4 header.
D. It translates the^ IPv4 destination address into a new NAT64 state.
E. It performs an IPv6 route lookup.

Answer: A

QUESTION 304
Which command do you enter to display log messages with a timestamp that includes the length of time since the device was last rebooted?

A. service timestamps log uptime
B. logging facility 20
C. service timestamps debugging localtime msec
D. logging console errors
E. logging monitor 7
F. service timestamps log datetime msec

Answer: A

QUESTION 305
Which option must be configured on a target device to use time stamping to accurately represent response times using IP SLA?

A. Responder
B. Jitter value
C. TCP Connect
D. ICMP Echo

Answer: D

QUESTION 306
Refer to the exhibit. Which option describes why the EIGRP neighbors of this router are not learning routes that are received from OSPF?

A. The subnet defined in OSPF is not part of area 0.
B. Default metrics are not configured under EIGRP.
C. There is no overlap in the subnets advertised.
D. The routing protocols do not have the same AS number.

Answer: B

QUESTION 307
Which two options are requirements for EIGRP authentication? (Choose two)

A. A crypto map must be configured.
B. The Authentication key must be configured under the interface running EIGRP.
C. The authentication key must be configured within the EIGRP routing configuration.
D. The authentication key IDs must match between two neighbors.
E. A separate key chain must be configured.
F. AN IPsec profile must be configured.

Answer: BD

QUESTION 308
A network engineer is troubleshooting connectivity issues with a directly connected RIPng neighbor. Which command should directly connected RIPng neighbor adjacencies only?

A. router#show ipv6 rip next-hops
B. router#show ip rip neighbors
C. router#show ipv6 routers
D. router#show ipv6 rip database

Answer: A

QUESTION 309
Which security feature can you enable to control access to the vty lines on a router?

A. exec-time out
B. logging
C. username and password
D. transport output

Answer: C

QUESTION 310
A network engineer wants an NTP clients to be able to update the local system without updating or synchronizing with the remote system.
Which option for the ntp access-group command is needed to accomplish this?

A. serve
B. query-only
C. serve-only
D. peer

Answer: A

2017 New 300-101 Questions and Answers Full Version: https://www.braindump2go.com/300-101.html , All New Questions are updated here everyday!

Reply