Which two EIGRP routes will be seen in the routing table of router R3?

New 300-101 Exam Questions and Answers Updated Recently (4/Nov/2016):

NEW QUESTION 184
What command can you enter to configure an enable password that uses an encrypted password from another configuration?

A. enable secret $abc%!e.Cd34$!ao0
B. enable secret 7 Sabc%!e.Cd34$!ao0
C. enable secret 0 Sabc%U*.Cd34$!ao0
D. enable secret 5 $abc%!e.Cd34$!ao0
E. enable secret 15 $abc%ie.Cd34$!ao0
F. enable secret 6 $abc%!e.Cd34$!ao0

Answer: D

NEW QUESTION 185
A network engineer receives reports about poor voice quality issues at a remote site. The network engineer does a packet capture and sees out-of-order packets being delivered. Which option can cause the VOIP quality to suffer?

A. traffic over backup redundant links
B. misconfigured voice vlan
C. speed duplex link issues
D. load balancing over redundant links

Answer: D
Explanation:
In traditional packet forwarding systems, using different paths have varying latencies that cause out of order packets, eventually resulting in far lower performance for the network application. Also , if some packets are process switched quickly by the routing engine of the router while others are interrupt switched (which takes more time) then it could result in out of order packets. The other options would cause packet drops or latency, but not out of order packets.

NEW QUESTION 186
What is the administrative distance for EBGP?

A. 200
B. 30
C. 70
D. 20

Answer: D

NEW QUESTION 187
Considering the IPv6 address independence requirements, which process do you avoid when you use NPTv6 for translation?

A. rewriting of higher layer information
B. checksum verification
C. ipv6 duplication and conservation
D. IPSEC AH header modification

Answer: A
Explanation:
The IPv6-to-IPv6 Network Prefix Translation (NPTv6) serves as a useful mechanism for implementing address independence in an IPv6 environment. A major benefit associated with NPTv6 is the fact that it avoids the requirement for an NPTv6 Translator to rewrite the transport layer headers which reduces the load on network devices.

cisco.com/c/en/us/td/docs/ios-xml/ios/ipaddr_nat/configuration/xe-16/nat-xe-16-book/iadnat-asr1k-nptv6.html

NEW QUESTION 188
What is the optimal location from which to execute a debug command that produces an excessive amount of information?

A. Vty lines
B. SNMP commands
C. A console port
D. An AUX port

Answer: A
Explanation:
cisco.com/c/en/us/support/docs/dial-access/integrated-services-digital-networks-isdn-channel-associated-signaling-cas/10374-debug.html

NEW QUESTION 189
A network engineer is configuring the router for NetFlow data exporting. What is required in order for NDE to begin exporting data?

A. Source
B. Flow mask
C. Destination
D. Interface type
E. Traffic type
F. NetFlow version

Answer: C
Explanation:
NetFlow Multiple Export Destinations–To configure redundant NDE data streams, which improves the probability of receiving complete NetFlow data, you can enter the ip flow-export destination command twice and configure a different destination IP address in each command. Configuring two destinations increases the RP CPU utilization, as you are exporting the data records twice.

cisco.com/en/US/docs/general/Test/dwerblo/broken_guide/nde.html#wp1139278

NEW QUESTION 190
Refer to the exhibit. Router 1 cannot ping router 2 via the Frame Relay between them. Which two statements describe the problems? (Chooses two.)
Image URL: examgod.com/plimages/4-Nov-2016-New-300-101-Dumps-with-VCE-an_8F09/passleader-210-065-dumps-1901_thumb.jpg

A. Encapsulation is mismatched.
B. Frame Relay map is configured.
C. DLCI is active.
D. DLCI is inactive or deleted.
E. An access list is needed to allow ping

Answer: AD
Explanation:
Frame Relay: Cannot ping Remote Router :
1-Encapsulation mismatch has occurred.
2-DLCI is inactive or has been deleted.
3-DLCI is assigned to the wrong subinterface.
4-An access list was misconfigured.
5-The frame-relay map command is missing.
6-No broadcast keyword is found in frame-relay map statements.

NEW QUESTION 191
At which layer does Cisco Express Forwarding use adjacency tables to populate addressing information?

A. Layer4
B. Layer 2
C. Layer 1
D. Layer 3

Answer: B
Explanation:
Adjacency table – Nodes in the network are said to be adjacent if they can reach each other with a single hop across a link layer. In addition to the FIB, CEF uses adjacency tables to prepend Layer 2 addressing information. The adjacency table maintains Layer 2 next-hop addresses for all FIB entries.

cisco.com/c/en/us/support/docs/routers/12000-series-routers/47321-ciscoef.html

NEW QUESTION 192
A network engineer wants to ensure an optimal end-to-end delay bandwidth product. The delay is less than 64 KB. Which TCP feature ensures steady state through put?

A. Window scaling
B. Network buffers
C. Round-trip timers
D. TCP acknowledgments

Answer: A
Explanation:
Many options can be carried in a TCP header. Those relevant to TCP performance include Window-scale option. Window-scale option:
This option is intended to address the issue of the maximum window size in the face of paths that exhibit a high-delay bandwidth product.
This option allows the window size advertisement to be right-shifted by the amount specified (in binary arithmetic, a right-shift corresponds to a multiplication by 2).
Without this option, the maximum window size that can be advertised is 65,535 bytes (the maximum value obtainable in a 16-bit field). The limit of TCP transfer speed is effectively one window size in transit between the sender and the receiver. For high-speed, long-delay networks, this performance limitation is a significant factor, because it limits the transfer rate to at most 65,535 bytes per round-trip interval, regardless of available network capacity.
Use of the window-scale option allows the TCP sender to effectively adapt to high-band-width, high-delay network paths, by allowing more data to be held in flight.
The maximum window size with this option is 230 bytes. This option is negotiated at the start of the TCP connection, and can be sent in a packet only with the SYN flag.
Note that while an MTU discovery process allows optimal setting of the maximum-receive-segment-size option, no corresponding bandwidth delay product discovery allows the reliable automated setting of the window-scale option.

cisco.com/c/en/us/about/press/internet-protocol-journal/back-issues/table-contents-5/ipj-archive/article09186a00800c8417.html

NEW QUESTION 193
A network administrator creates a static route that points directly to a multi-access interface, instead of the next-hop IP address. The administrator notices that Cisco Express Forwarding ARP requests are being sent to all destinations. Which issue might this configuration create?

A. Low bandwidth usage
B. High memory usage
C. Cisco Express Forwarding routing loop
D. High bandwidth usage
E. IP route interference

Answer: C
Explanation:
cisco.com/c/en/us/support/docs/ip/express-forwarding-cef/26083-trouble-cef.html

NEW QUESTION 194
Refer to the exhibit. Which three NTP features can be deduced on the router? (choose three)
Image URL: examgod.com/plimages/4-Nov-2016-New-300-101-Dumps-with-VCE-an_8F09/passleader-210-065-dumps-1941_thumb.png

A. only accepts time requests from 192.168.1.1
B. only handle four requests at a time
C. only is in stratum 4
D. only updates its time from 192.168.1.1
E. only accepts time requests from 192.168.1.4
F. only updates its time from 192.168.1.4

Answer: ACF
Explanation:
IOS router defines the following four types of access for NTP:
1) Peer – permits router to respond to NTP requests and accept NTP updates. NTP control queries are also accepted. This is the only class which allows a router to be synchronized by other devices.
2) Serve – permits router to reply to NTP requests, but rejects NTP updates (e.g. replies from a server or update packets from a peer). Control queries are also permitted.
3) Serve-only – permits router to respond to NTP requests only. Rejects attempt to synchronize local system time, and does not access control queries.
4) Query-only – only accepts NTP control queries. No response to NTP requests are sent, and no local system time synchronization with remote system is permitted.

NEW QUESTION 195
……

NEW QUESTION 212
Refer to the exhibit. A network engineer is troubleshooting a DMVPN setup between the hub and the spoke. The engineer executes the command show crypto isakmp sa and observes the output that is displayed. What is the problem?
Image URL: examgod.com/plimages/4-Nov-2016-New-300-101-Dumps-with-VCE-an_8F09/passleader-210-065-dumps-2121_thumb.jpg

A. That ISAKMP is not enabled
B. That ISAKMP is using default settings
C. An incompatible IP sec transform set
D. An incompatible ISAKMP policy

Answer: B
Explanation:
cisco.com/c/en/us/support/docs/security-vpn/ipsec-negotiation-ike-protocols/5409-ipsec-debug-00.html

NEW QUESTION 213
……

P.S. These New 300-101 Exam Questions Were Just Updated From The Real 300-101 Exam, You Can Get The Newest 300-101 Dumps In PDF And VCE From — http://www.passleader.com/300-101.html (230q)

Good Luck !!!

New 300-101 Exam Questions and Answers Updated Recently (3/Feb/2017):

NEW QUESTION 231
Refer to exhibit. What is indicated by the show ip cef command for an address?
Image URL: examgod.com/plimages/553c70e0915d_742E/passleader-300-101-dumps-2311.jpg

A. CEF is unable to get routing information for this route.
B. CEF cannot switch packet for this route and passes it to the next best switching method.
C. A valid entry and is pointed to hardware based forwarding.
D. CEF cannot switch packet for this route and drops it.

Answer: B
Explanation:
Glean adjacency – in short when the router is directly connected to hosts the FIB table on the router will maintain a prefix for the subnet rather than for the individual host prefix. This subnet prefix points to a GLEAN adjacency.
Punt adjacency – When packets to a destination prefix can’t be CEF Switched, or the feature is not supported in the CEF Switching path, the router will then use the next slower switching mechanism configured on the router.

NEW QUESTION 232
Refer to Exhibit. Which two reasons for IP SLA tracking failure are likely true? (Choose Two.)
Image URL: examgod.com/plimages/553c70e0915d_742E/passleader-300-101-dumps-2321.jpg

A. The source-interface is configured incorrectly.
B. The destination must be 172.30.30.2 for icmp-echo.
C. A route back to the R1 LAN network is missing in R2.
D. The default route has wrong next hop IP address.
E. The threshold value is wrong.

Answer: BE

NEW QUESTION 233
A network engineer enables OSPF on a Frame Relay WAN connection to various remote sites, but no OSPF adjacencies come up. Which two actions are possible solutions for this issue? (Choose Two.)

A. Change the network type to point-to-multipoint under WAN interface.
B. Enable virtual links.
C. Change the network type to nonbroadcast multipoint access.
D. Configure the neighbor command under OSPF process for each remote site.
E. Ensure that the OSPF process number matches among all remote sites.

Answer: AC

NEW QUESTION 234
A network engineer applies the command ip tcp adjust-mss under interface configuration mode. What is the result?

A. The probability of SYN packet truncation is increased.
B. The UDP session is inversely affected.
C. The probability of dropped or segmented TCP packets is decreased.
D. The optimum MTU value for the interface is set.

Answer: C

NEW QUESTION 235
Which command configures a PPPoE client and specifies dial-on-demand routing functionality?

A. pppoe-client dial-pool-number
B. PPPoE enable
C. interface dialer 1
D. encapsulation PPP

Answer: A

NEW QUESTION 236
……

P.S. These New 300-101 Exam Questions Were Just Updated From The Real 300-101 Exam, You Can Get The Newest 300-101 Dumps In PDF And VCE From — http://www.passleader.com/300-101.html (243q VCE and PDF)

Good Luck!

New 300-101 Exam Questions and Answers Updated Recently (2/June/2017):

NEW QUESTION 296
Which type of access list allows granular session filtering for upper-level protocols?

A. content-based access lists
B. context-based access lists
C. reglexive access lists
D. extended access lists

Answer: D

NEW QUESTION 297
Which three configuration parameters can a DHCPV6 pool contain? (Choose three.)

A. domain search list
B. router IP
C. default gateway
D. prefix delegation
E. DNS servers
F. subnet mask

Answer: DEF

NEW QUESTION 298
Which statement about local policy routing is true?

A. It is used to policy route packets that are generated by the device.
B. It requires all packets to be packet switched.
C. It is used to policy route packets that pass through the device.
D. It requires all packets to be CEF switched.
E. It supports IPv4 packets only.
F. It requires an ip address or access list as the matching criteria.

Answer: A

NEW QUESTION 299
Which SNMP verification command shows the encryption and authentication protocols that are used in SNMPV3?

A. show snmp group
B. show snmp user
C. show snmp
D. show snmp view

Answer: B

NEW QUESTION 300
Which type of information is displayed when a network engineer executes the show track 1 command on the router?

A. information about tracking list 1.
B. time to next poll for track object 1.
C. information about the IP route track table.
D. tracking information statistics.

Answer: A

NEW QUESTION 301
Which command sequence can you enter on a router to configure Unicast Reverse Path Forwarding in loose mode?

A. interface GigabitEthernet0/0
ip verigy unicast source reachable-via all
B. interface GigabitEthernet0/0
ip verigy unicast source reachable-via loose
C. interface GigabitEthernet0/0
ip verigy unicast source reachable-via any
D. interface GigabitEthernet0/0
ip verigy unicast source reachable-via rx

Answer: C

NEW QUESTION 302
Where can NetFlow export data for long term storage and analysis?

A. syslog
B. collector
C. another network device
D. flat file

Answer: B

NEW QUESTION 303
Which option is the first task that a device that is configured with NAT64 performs when it receives an incoming IPv6 packet that matches the stateful NAT64 prefix?

A. It translates the IPv6 header into an IPv4 header.
B. It checks the IPv6 packet against the NAT64 stateful prefix.
C. It translates the IPv6 source address to an IPv4 header.
D. It translates the^ IPv4 destination address into a new NAT64 state.
E. It performs an IPv6 route lookup.

Answer: A

NEW QUESTION 304
Which command do you enter to display log messages with a timestamp that includes the length of time since the device was last rebooted?

A. service timestamps log uptime
B. logging facility 20
C. service timestamps debugging localtime msec
D. logging console errors
E. logging monitor 7
F. service timestamps log datetime msec

Answer: A

NEW QUESTION 305
Which option must be configured on a target device to use time stamping to accurately represent response times using IP SLA?

A. Responder
B. Jitter value
C. TCP Connect
D. ICMP Echo

Answer: D

NEW QUESTION 306
Refer to the exhibit. Which option describes why the EIGRP neighbors of this router are not learning routes that are received from OSPF?
router eigrp 1
redistribute ospf 100
network 10.10.10.0 0.0.0.255
auto-summary
!
router ospf 100
network 172.16.0.0 0.0.255.255 area 100
redistribute eigrp 1

A. The subnet defined in OSPF is not part of area 0.
B. Default metrics are not configured under EIGRP.
C. There is no overlap in the subnets advertised.
D. The routing protocols do not have the same AS number.

Answer: B

NEW QUESTION 307
Which two options are requirements for EIGRP authentication? (Choose two.)

A. A crypto map must be configured.
B. The Authentication key must be configured under the interface running EIGRP.
C. The authentication key must be configured within the EIGRP routing configuration.
D. The authentication key IDs must match between two neighbors.
E. A separate key chain must be configured.
F. AN IPsec profile must be configured.

Answer: BD

NEW QUESTION 308
A network engineer is troubleshooting connectivity issues with a directly connected RIPng neighbor. Which command should directly connected RIPng neighbor adjacencies only?

A. router#show ipv6 rip next-hops
B. router#show ip rip neighbors
C. router#show ipv6 routers
D. router#show ipv6 rip database

Answer: A

NEW QUESTION 309
Which security feature can you enable to control access to the vty lines on a router?

A. exec-time out
B. logging
C. username and password
D. transport output

Answer: C

NEW QUESTION 310
A network engineer wants an NTP clients to be able to update the local system without updating or synchronizing with the remote system. Which option for the ntp access-group command is needed to accomplish this?

A. serve
B. query-only
C. serve-only
D. peer

Answer: A

NEW QUESTION 311
……

P.S. These New 300-101 Exam Questions Were Just Updated From The Real 300-101 Exam, You Can Get The Newest 300-101 Dumps In PDF And VCE From — http://www.passleader.com/300-101.html (332q VCE and PDF)

Good Luck!

Besides, part of the new 300-115 dumps are available here:

http://www.ciscobraindump.com/?s=300-115

Best Regards!

New 300-101 Exam Questions and Answers (4/July/2017 Updated):

NEW QUESTION 378
What is used in EIGRP metric calculation?

A. maximum delay
B. minimum delay
C. average delay
D. minimum interface bandwidth

Answer: D

NEW QUESTION 379
What show command is used here?
TCB Local Address Foreign Address (state)
6523A4FC 10.1.25.3.11000 10.1.25.3.23 ESTAB
65239A84 10.1.25.3.23 10.1.25.3.11000 ESTAB
653FCBBC *.1723 *.* LISTEN

A. show tcp brief
B. show tcp brief all
C. show tcp brief numeric
D. show tcp brief ip

Answer: C

NEW QUESTION 380
You need the IP address of the devices with which the router has established an adjacency. Also, the retransmit interval and the queue counts for the adjacent routers need to be checked. What command will display the required information?

A. show ip eigrp adjacency
B. show ip eigrp topology
C. show ip eigrp interfaces
D. show ip eigrp neighbor

Answer: D

NEW QUESTION 381
You get a call from a network administrator who tells you that he typed the following into his router:
Router(config)#router ospf 1
Router(config-router)#network 10.0.0.0 255.0.0.0 area 0
He tells you he still can’t see any routes in the routing table. What configuration error did the administrator make?

A. The wildcard mask is incorrect
B. The OSPF area is wrong
C. The OSPF process ID is incorrect
D. The AS configuration is wrong

Answer: A

NEW QUESTION 382
If routers in a single area are configured with the same priority value, what value does a router use for the OSPF Router ID in the absence of a loopback interface?

A. The lowest IP address of any physical interface
B. The highest IP address of any physical interface
C. The lowest IP address of any logical interface
D. The highest IP address of any logical interface

Answer: B

NEW QUESTION 383
Where are EIGRP successor routes stored?

A. In the routing table only
B. In the neighbor table only
C. In the topology table only
D. In the routing table and the topology table
E. In the routing table and the neighbor table

Answer: D

NEW QUESTION 384
Which location is traffic from IP SLAs?

A. core edge
B. access edge
C. WAN edge
D. Distribution edge
E. User edge

Answer: C

NEW QUESTION 385
Which option is invalid redistribute from EIGRP into OSPF?

A. ACL
B. tag
C. metric
D. route map

Answer: A

NEW QUESTION 386
……

P.S. Get The Newest 300-101 Dumps In PDF And VCE From — http://www.passleader.com/300-101.html (403q VCE and PDF)

Good Luck!

New 300-101 Exam Questions and Answers (15/Aug/2017 Updated):

NEW QUESTION 423
Which two methods use IPsec to provide secure connectivity from the branch office to the headquarters office? (Choose two.)

A. DMVPN
B. MPLS VPN
C. Virtual Tunnel Interface (VTI)
D. SSL VPN
E. PPPoE

Answer: AC

NEW QUESTION 424
Which two statements about Frame Relay Point-to-Point connections are true? (Choose two.)

A. Changing a point-to-point sub interface to a different type requires the device to be reloaded.
B. They use two DLCIs to communicate with multiple endpoints over the Frame Relay cloud.
C. The device can establish a point-to-point connection to the cloud without a DLCI.
D. They can operate normally without a DLCI map.
E. Each physical interface that extends to the Frame Relay cloud can support a single SVC.

Answer: AB

NEW QUESTION 425
What is the international standard for transmitting data over a cable system?

A. PPPoE
B. DOCSIS
C. CMTS
D. AAL5

Answer: B

NEW QUESTION 426
Which interface type does a PPPoE client use to establish a session?

A. Physical
B. loopback
C. visual-template
D. dialer

Answer: D

NEW QUESTION 427
The Cisco SA 500 Series Security Appliances are built specifically for businesses with less than 100 employees. What are three important benefits of this device? (Choose three.)

A. business-grade firewall
B. premium support via SMART net
C. site-to-site VPN for remote offices
D. Cisco IOS software-based
E. email security
F. XML support

Answer: ACE

NEW QUESTION 428
Which Cisco Express Forwarding component maintains Layer 2 addressing information?

A. dCEF
B. adjacency table.
C. FIB
D. fast switching
E. RIB

Answer: B
Explanation:
Adjacency TablesNodes in the network are said to be adjacent if they can reach each other with a single hop across a link layer. In addition to the FIB, CEF uses adjacency tables to prepend Layer 2 addressing information. The adjacency table maintains Layer 2 next-hop addresses for all FIB entries.

NEW QUESTION 429
……

NEW QUESTION 430
Which two debug commands can you use to view issues with CHAP and PAP authentication? (Choose two.)

A. debug tacacs
B. debug ppp authentication
C. debug radius
D. debug aaa authentication
E. debug ppp negotiation

Answer: BE

NEW QUESTION 431
Which DSL encapsulation method requires client software running on the end-user PC that is directly connected to a DSL modem?

A. PPPoA
B. PPPoE
C. PPP
D. L2TP
E. ATM

Answer: B

NEW QUESTION 432
By default, which type of IPv6 address is used to build the EUI-64 bit format?

A. unique-local address
B. IPv4-compatible IPv6 address
C. link-local address
D. aggregatable-local address

Answer: C

NEW QUESTION 433
For a GRE tunnel to be up between two routers, which of the following must be configured?

A. Loopback Interface
B. IP reachability between the loopback interfaces
C. Dynamic Routing between routers
D. Tunnel interfaces must be in the same subnet

Answer: D

NEW QUESTION 434
Which two statements about configuring Frame Relay point-to-multipoint connections are true? (Choose two.)

A. They ignore the broadcast keyword in the frame-relay DLCI mapping.
B. They require the same DLCI on each side of the link.
C. Changing a point-to-multipoint subinterface to a different type requires the interface to be deleted and recreated.
D. They require the frame-relay mapping command to be configured.
E. They require inverse ARP.

Answer: DE

NEW QUESTION 424
……

P.S. You Can Get The Newest 300-101 Dumps In PDF And VCE From — https://www.passleader.com/300-101.html (470q VCE and PDF)

Good Luck!

New 300-101 Exam Questions Updated Recently (2/Nov/2017):

NEW QUESTION 464
Refer to the exhibit. How can you configure a second export destination for IP address 192.168.10.1?
configure terminal
ip flow-export destination 192.168.10.1 9991
ip flow-export version 9

A. specify a different TCP port
B. specify a different UDP port
C. specify a VRF
D. configure a version 5 flow-export to the same destination
E. specify a different flow ID

Answer: C

NEW QUESTION 465
Which value does Frame Relay use to identify a connection between a DTE and DCE?

A. DLCI
B. IP address
C. MAC address
D. VLAN ID

Answer: A

NEW QUESTION 466
Which two options are limitations of Stateful NAT64? (Choose two.)

A. it is unable to route VRF traffic
B. it is unable to route multicast traffic
C. it supports FTP traffic only with an ALG
D. it supports DNS64 only
E. layer 4 supports TCP only

Answer: AB

NEW QUESTION 467
If you want to migrate an IS-IS network to another routing protocol with ……? (Choose two.)

A. UDP
B. Internal BGP
C. TCP/IP
D. EIGRP
E. OSPF
F. RIP

Answer: DE

NEW QUESTION 468
IP CEF load-sharing options ……? (Choose three.)

A. Tunnel
B. Universal
C. Include-ports
D. Source
E. Destination

Answer: ABC

NEW QUESTION 469
What is the minimum privilege level to enter all commands in usermode?

A. Level14
B. Level0
C. Level1
D. Level15

Answer: C

NEW QUESTION 470
Which two statements about password-protecting device access are true? (Choose two)

A. The more system:running-config command displays encrypted passwords in clear text.
B. The service password-encryption command forces a remote device to encrypt the password.
C. A network administrator can recover an encrypted password.
D. The privilege level command controls the commands a specific user can execute.
E. The password can be encrypted in the running configuration.

Answer: DE

NEW QUESTION 471
Frame Relay LMI autosense. Which statements are true? (Choose two.)

A. Line should be up and protocol should be down.
B. Protocol must be up.
C. It only works on DTEs.
D. It only works on DCEs.

Answer: AC

NEW QUESTION 472
Which two protocols can cause TCP starvation? (Choose two.)

A. TFTP
B. SNMP
C. SMTP
D. HTTPS
E. FTP

Answer: AB

NEW QUESTION 473
……

P.S. These New 300-101 Exam Questions Were Just Updated From The Real 300-101 Exam, You Can Get The Newest 300-101 Dumps In PDF And VCE From — https://www.passleader.com/300-101.html (489q VCE and PDF)

Good Luck!

Pass4surekey is most popular site which provides latest dumps question answers to pass your certification exam. Get Updated Cisco 300-101 dumps, our expert made dumps will help you to pass your exam easily.All 300-101 question answers are latest and verified by IT experts.Our 300-101 dumps are consist of professionally planned and verified 300-101 questions answers. Our support team is always here to help! If you have any further query, just visit us. http://300-101pdf.blogspot.com/