Which answer gives the reason for the omission?

Router R1 has working interfaces S0/0, S0/1, and S0/2, with IP address/prefix combinations
of 10.10.10.1/24, 10.10.11.2/24, and 10.10.12.3/22. R1’s configuration includes the
commands router eigrp 9 and network 10.0.0.0. The show ip eigrp interfaces command lists
S0/0 and S0/1 in the command output, but not S0/2. Which answer gives the reason for the
omission? (Choose two answers.)

Router R1 has working interfaces S0/0, S0/1, and S0/2, with IP address/prefix combinations
of 10.10.10.1/24, 10.10.11.2/24, and 10.10.12.3/22. R1’s configuration includes the
commands router eigrp 9 and network 10.0.0.0. The show ip eigrp interfaces command lists
S0/0 and S0/1 in the command output, but not S0/2. Which answer gives the reason for the
omission? (Choose two answers.)

A.
R1 has EIGRP neighbors reachable via S0/0 and S0/1, but not via S0/2, so it is not
included.

B.
S0/2 may currently be in a state other than up/up.

C.
The network 10.0.0.0 command requires the use of mask 255.0.0.0 due to EIGRP being
classful by default.

D.
S0/2 may be configured as a passive interface.

Explanation:
The show ip eigrp interfaces command displays working (up/up) interfaces on which EIGRP
has been enabled but omits passive interfaces. A failure of the interface, or making the
interface passive, would omit the interface from the output of this command.



Leave a Reply 4

Your email address will not be published. Required fields are marked *

twenty − thirteen =


KurpLondon

KurpLondon

B and D

Alex

Alex

In first line was “Router R1 has working interfaces S0/0, S0/1, and S0/2” result al interfaces is up/up and the good answer is D.

Bernhard Gassner

Bernhard Gassner

(2/Nov/2017 Updated) New 300-101 Exam Questions:

NEW QUESTION 468
If you want to migrate an IS-IS network to another routing protocol with ……? (Choose two.)

A. UDP
B. Internal BGP
C. TCP/IP
D. EIGRP
E. OSPF
F. RIP

Answer: DE

NEW QUESTION 469
IP CEF load-sharing options ……? (Choose three.)

A. Tunnel
B. Universal
C. Include-ports
D. Source
E. Destination

Answer: ABC

NEW QUESTION 470
What is the minimum privilege level to enter all commands in usermode?

A. Level14
B. Level0
C. Level1
D. Level15

Answer: C

NEW QUESTION 471
Which two statements about password-protecting device access are true? (Choose two)

A. The more system:running-config command displays encrypted passwords in clear text.
B. The service password-encryption command forces a remote device to encrypt the password.
C. A network administrator can recover an encrypted password.
D. The privilege level command controls the commands a specific user can execute.
E. The password can be encrypted in the running configuration.

Answer: DE

NEW QUESTION 472
Frame Relay LMI autosense. Which statements are true? (Choose two.)

A. Line should be up and protocol should be down.
B. Protocol must be up.
C. It only works on DTEs.
D. It only works on DCEs.

Answer: AC

NEW QUESTION 473
Which two protocols can cause TCP starvation? (Choose two.)

A. TFTP
B. SNMP
C. SMTP
D. HTTPS
E. FTP

Answer: AB

NEW QUESTION 474
Refer to the exhibit. How can you configure a second export destination for IP address 192.168.10.1?
configure terminal
ip flow-export destination 192.168.10.1 9991
ip flow-export version 9

A. specify a different TCP port
B. specify a different UDP port
C. specify a VRF
D. configure a version 5 flow-export to the same destination
E. specify a different flow ID

Answer: C

NEW QUESTION 475
Which value does Frame Relay use to identify a connection between a DTE and DCE?

A. DLCI
B. IP address
C. MAC address
D. VLAN ID

Answer: A

NEW QUESTION 476
Which two options are limitations of Stateful NAT64? (Choose two.)

A. it is unable to route VRF traffic
B. it is unable to route multicast traffic
C. it supports FTP traffic only with an ALG
D. it supports DNS64 only
E. layer 4 supports TCP only

Answer: AB

NEW QUESTION 477
……

Get The Newest 300-101 Dumps In PDF And VCE From — https://www.passleader.com/300-101.html (489q VCE and PDF)

Good Luck!