Which two are configuration elements selected during initial setup of the Cisco MDS 9100 Series
Fibre Channel Switches? (Choose two.)
A.
Telnet bits
B.
SNMPv3 community strings
C.
Zone port distribution
D.
Enforce password complexity
E.
Default switchport mode F
D: is wrong, it must be C & E
setup configures switchport state & trunk mode
and the zonepolicy and zoneset-distribution
http://www.cisco.com/en/US/docs/storage/san_switches/mds9000/sw/san-os/quick/guide/qcg_ins.html#wp1139649
output from setup:
switchname switch_name
interface mgmt0
ip address mgmt_IP_address
subnetmask mgmt0_ip_netmask
no shutdown
ip default-gateway default_gateway
telnet server enable
no ssh server enable
no system default switchport shutdown
system default switchport trunk mode on
no zone default-zone permit vsan 1-4093
zoneset distribute full vsan 1-4093
Would you like to edit the configuration? (yes/no) [n]: no
I agree with Wakky. Complex password is forced:
Step 4 Make sure you enter the password you wish to assign for the admin user name.
—- System Admin Account Setup —-
Enter the password for “admin”:
Tip If a password is trivial (short, easy-to-decipher), your password configuration is rejected. Be sure to configure a strong password. Passwords are case-sensitive. You must explicitly configure a password that meets the requirements listed in the “Configuring User Accounts” section in the Cisco MDS 9000 Family CLI Configuration Guide.
There is no such thing as zone port distribution
Passed my 640-916 exam yesterday! Scored 9XX/1000!
Questions were mainly on:
1. Concepts of Cisco Data Center Fundamentals, Data Center core layer, Data Center aggregation layer, Data Center access layer, Cisco Nexus product family, vPC, VDC, etc.
2. Data Center Unified Fabric, FCoE, VIFs, FEX products, etc.
3. Storage Networking, SAN/VSAN.
4. DC Virtualization, Device/Server Virtualization, Nexus 1000v/Nexus 1k.
5. Unified Computing, operation/connectivity/UCSM.
6. Others.
A lot of questions on vPC, VDC, FCoE, SAN/VSAN, Nexus 1000v, pay close attention to them!!!
Around 2 Drag and Drop questions (Network virtualization technology, WAAS component feature).
I mainly learned valid 640-916 dumps from PL here:
http://www.passleader.com/640-916.html (191Q VCE and PDF) (ATTENTION!!! ALL NEW QUESTIONS ARE AVAILABLE IN IT NOW!!!)
It is the most valid 640-916 dumps that I learned, ALL NEW QUESTIONS ARE AVAILABLE IN IT NOW!!! Recommend to you all!
What’s more,
That 191q dumps now are available here for free:
https://doc.co/xowmPQ
FYI! Good Luck!
Preparing to Configure the Switch
Before you configure a switch in the Cisco MDS 9000 Family for the first time, you need the following information:
Administrator password, including:
– Creating a password for the administrator (required).
– Creating an additional login account and password (optional).
IPv4 address or IPv6 address for the switch management interface—The management interface can be an out-of-band Ethernet interface or an in-band Fibre Channel interface (recommended).
If you are using an IPv4 address for the management interface, you need the following information:
– IPv4 subnet mask for the switch’s management interface (optional).
– Destination IPv4 prefix, destination IPv4 prefix subnet mask, and next hop IPv4 address, if you want to enable IP routing.
– IPv4 address of the default gateway (optional).
– SSH service on the switch—To enable this optional service, select the type of SSH key
(dsa/rsa/rsa1) and number of key bits (768 to 2048).
– DNS IPv4 address or IPv6 address (optional).
– Default domain name (optional).
– NTP server IPv4 address or IPv6 address (optional).
– SNMP community string (optional).
– Switch name—This is your switch prompt (optional).
link:http://www.cisco.com/c/en/us/td/docs/switches/datacenter/mds9000/sw/4_1/configuration/guides/cli_4_1/clibook/icfg.html