A new client has contacted you to design a WLAN solution for a new 30-foot high-bay warehouse that will use
high-lift electric forklifts. The warehouse is currently empty except for storage racks. The customer is planning
to continue to use their existing wireless barcode scanners and also deploy wireless IP phones for
communication. Which four issues do you need to consider prior to performing the site survey? (Choose four.)
A.
Which protocol do the wireless barcode scanners andIP phones need to use?
B.
Which types of goods will be stored in the warehouse and what is the expected average warehouse
capacity?
C.
Do any planned WLC locations exceed 100 meter cable distances?
D.
Is there sufficient clearance between the roof and the top of the racks for placing APs?
E.
What is the expected humidity level in the warehouse on average during the year?
F.
Are there any secure enclosures that use chain-link fence that will require wireless access?
hi, I don´t think that C is correct, I mean C and B have to be changed
BR
you’re right.
I passed the 642-732 exam yesterday. Total 60q, around 3-5 new questions. Learned passleader 642-732 dumps (http://www.passleader.com/642-732.html), all questions are available in it, valid enough for passing.
New 642-732 Exam Questions and Answers Updated Recently (12/Mar/2016):
NEW QUESTION 168
What is the attenuation of a wireless signal that passes through a cider block wall?
A. 3 dB
B. 4 dB
C. 6 dB
D. 12 dB
Answer: B
NEW QUESTION 169
After installation of a new data-only wireless network, an engineer found that RRM has set all of the APs to a power level of 1. Which option describes the reason for this?
A. APs are too far apart for the set data rates.
B. EDRRM is enabled.
C. APs should be manually set initially.
D. TPC needs to be enabled.
E. DTPC value is set too high.
F. High co-channel interference exists.
Answer: A
NEW QUESTION 170
Which three post-installation checks should an engineer perform after a new wireless installation? (Choose three.)
A. Check for co-channel interference.
B. Check for adequate signal levels as surveyed.
C. Conduct a passive survey of 802.11a and 802.11b.
D. Conduct a passive and active survey of each media type in use.
E. Verify that the minimum data rate is 24 Mbps.
F. Verify that the cell overlap is 20%.
Answer: ABD
NEW QUESTION 171
An engineer is preparing to conduct a site survey with AirMagnet. The engineer wants to capture all 802.11 traffic (not SSID specific) on the first walkthrough. Which survey mode should be used?
A. active
B. active with Iperf for greenfield: AP mode
C. active with Iperf for greenfield: SSID mode
D. passive
E. planning mode survey
Answer: D
NEW QUESTION 172
An engineer is conducting a site survey for use of Cisco 7925 wireless clients. Which two design criteria are necessary to ensure proper network design? (Choose two.)
A. 15 percent overlap
B. 20 percent overlap
C. 25 percent overlap
D. -65 dBm RSSI or better
E. -67 dBm RSSI or better
F. -72 dBm RSSI or better
Answer: BE
NEW QUESTION 173
An engineer is tasked with designing a WLAN. The customer is prioritizing data speeds to the desktop, but is also entertaining the idea of adding 802.11 phones in the future. Given this information, how should the engineer conduct the survey?
A. consider the employee head count in congested office space and limit the edge of each cell to an RSSI of -67mW
B. restrict AP cell edges to -67dB and be sure to strategically place APs in congested office spaces
C. co-locate access points when possible to cover high user areas and place APs at each corner of the facility
D. stagger the AP placements, and be sure to have a high signal to noise ratio that will accommodate the future VoIP devices
Answer: B
NEW QUESTION 174
An engineer is installing a wireless network in an industrial area with extreme temperatures and a significant amount of dust. Which enclosure should be used to protect the APs?
A. NEMA
B. ACU
C. WLSE
D. ADU
Answer: A
NEW QUESTION 175
In an outdoor mesh environment, which is the purpose of deploying one of the access points relatively higher than the others?
A. The MAPs need to be mounted higher than the first hop RAPs so that the mesh units can accomplish radio line of sight.
B. Elevated MAPs are connected to the switches, providing better bandwidth that all the RAPs utilize for client connectivity.
C. An AP deployed as a RAP needs to be mounted in a higher elevation to provide clear connectivity to first hop MAPs.
D. Root APs need clear line of sight to provide the best bandwidth to all of its RAPs, so the higher the better.
Answer: C
NEW QUESTION 176
A site survey proposes placement of new APs to replace older APs. Which three options are three potential placements of the new APs? (Choose three.)
A. Use the old placements where they are near the proposed location.
B. Add APs from the site survey that have no APs in older installation.
C. Mount new APs on the exact location according to site survey report.
D. Use network cables and mounting brackets from the older installation.
E. Deploy APs every 4000 square feet.
F. Deploy APs every 3000 square feet.
Answer: ABC
NEW QUESTION 177
A company has requested an indoor wireless survey that supports 5GHz radio, 3×4 MIMO technology, and 3 spatial streams. Which AP is used to perform this survey?
A. 600
B. 1242
C. 1600
D. 2600
E. 3600
Answer: D
NEW QUESTION 178
An engineer is configuring an AP for a site survey. How should the transmit power be configured?
A. Set to maximum power.
B. Set to one level below full power.
C. Enable DTPC.
D. Set to one level above the lowest power level.
Answer: B
NEW QUESTION 179
……
P.S. These New 642-732 Exam Questions Were Just Updated From The Real 642-732 Exam, You Can Get The Newest 642-732 Dumps In PDF And VCE From — http://bitly.com/642-732-exam (197q)
Good Luck !!!