Refer to the exhibit. On the basis of the information provided in the exhibit, which two sets of procedures are best practices for Layer 2 and 3 failover alignment? (Choose two.)
A.
Configure the D-SW1 switch as the active HSRP router and the STP root for all VLANs. Configure the D-SW2 switch as the standby HSRP router and backup STP root for all VLANs.
B.
Configure the D-SW1 switch as the standby HSRP router and the STP root for VLANs 11 and 110. Configure the D-SW2 switch as the standby HSRP router and the STP root for VLANs 12 and 120.
C.
Configure the D-SW1 switch as the active HSRP router and the STP root for VLANs 11 and 110. Configure the D-SW2 switch as the active HSRP router and the STP root for VLANs 12 and 120.
D.
Configure the D-SW2 switch as the active HSRP router and the STP root for all VLANs. Configure the D-SW1 switch as the standby HSRP router and backup STP root for all VLANs.
E.
Configure the D-SW1 switch as the active HSRP router and the backup STP root for VLANs 11 and 110. Configure the D-SW2 switch as the active HSRP router and the backup STP root for VLANs 12 and 120.
F.
Configure the D-SW1 switch as the standby HSRP router and the backup STP root for VLANs 12 and 120. Configure the D-SW2 switch as the standby HSRP router and the backup STP root for VLANs 11 and 110.
Explanation:
Basically, each of the routers that provides redundancy for a given gateway address is assigned to a common HSRP group. One router is elected as the primary, or active, HSRP router, another is elected as the standby HSRP router, and all the others remain in the listen HSRP state. The routers exchange HSRP hello messages at regular intervals, so they can remain aware of each other’s existence, as well as that of the active router.
HSRP election is based on a priority value (0 to 255) that is configured on each router in the group. By default, the priority is 100. The router with the highest priority value (255 is highest) becomes the active router for the group. If all router priorities are equal or set to the default value, the router with the highest IP address on the HSRP interface becomes the active router. To set the priority, use the following interface configuration command:
Switch(config-if)# standby group priority priorityWhen HSRP is configured on an interface, the router progresses through a series of states before becoming active. This forces a router to listen for others in a group and see where it fits into the pecking order. The HSRP state sequence is Disabled, Init, Listen, Speak, Standby, and, finally, Active.
You can configure a router to preempt or immediately take over the active role if its priority is the highest at any time. Use the following interface configuration command to allow preemption:
Switch(config-if)# standby group preempt [delay seconds]
Fortunately, there are a number of treatments available if you
suffer from this unfortunate condition. The platinum blonde is a much sought after persona, and the look,
an elegant and beautiful one if carried off properly, is a much desired and much employed part of dressing
up. Have Some Much more Derm – Organic Care For The Locks.
Yes, fake tan can look really good when done properly but often by doing it our self’s and even sometimes professionally
it can turn out bad and embarrassing. In order to get a rich and spotless tan while keeping your skin smooth and glowing, it is necessary to use the best quality
tanning products. Dark sunsation self tanning lotion is a perfect solution for immediate tanning needs.
One more thing on which you need to pay attention to is fats and this is something that you should not be consumed in the large amount.
Don’t let yourself be baffled, acquiring benefits on the <. HCG diet materials stress the importance of sticking to this diet.