Topology Overview (Actual Troubleshooting lab design is for below network design)
Client Should have IP 10.2.1.3
EIGRP 100 is running between switch DSW1 & DSW2
OSPF (Process ID 1) is running between R1, R2, R3, R4
Network of OSPF is redistributed in EIGRP
BGP 65001 is configured on R1 with Webserver cloud AS 65002
HSRP is running between DSW1 & DSW2 Switches
The company has created the test bed shown in the layer 2 and layer 3 topology exhibits.
This network consists of four routers, two layer 3 switches and two layer 2 switches.
In the IPv4 layer 3 topology, R1, R2, R3, and R4 are running OSPF with an OSPF process
number 1.
DSW1, DSW2 and R4 are running EIGRP with an AS of 10. Redistribution is enabled where
necessary.
R1 is running a BGP AS with a number of 65001. This AS has an eBGP connection to AS 65002
in the ISP’s network. Because the company’s address space is in the private range.
R1 is also providing NAT translations between the inside (10.1.0.0/16 & 10.2.0.0/16) networks and
outside (209.65.0.0/24) network.
ASW1 and ASW2 are layer 2 switches.
NTP is enabled on all devices with 209.65.200.226 serving as the master clock source.
The client workstations receive their IP address and default gateway via R4’s DHCP server.
The default gateway address of 10.2.1.254 is the IP address of HSRP group 10 which is running
on DSW1 and DSW2.
In the IPv6 layer 3 topology R1, R2, and R3 are running OSPFv3 with an OSPF process number
6.
DSW1, DSW2 and R4 are running RIPng process name RIP_ZONE.
The two IPv6 routing domains, OSPF 6 and RIPng are connected via GRE tunnel running over the
underlying IPv4 OSPF domain. Redistrution is enabled where necessary.
Recently the implementation group has been using the test bed to do a ‘proof-of-concept’ on
several implementations. This involved changing the configuration on one or more of the devices.
You will be presented with a series of trouble tickets related to issues introduced during these
configurations.
Note: Although trouble tickets have many similar fault indications, each ticket has its own issue
and solution.
Each ticket has 3 sub questions that need to be answered & topology remains same.
Question-1Fault is found on which device,
Question-2Fault condition is related to,
Question-3What exact problem is seen & what needs to be done for solution
=========================================
Client is unable to ping IP 209.65.200.241
Solution
Steps need to follow as below:-When we check on client 1 & Client 2 desktop we are not receiving DHCP address from R4
ipconfig
Client will be receiving IP address 10.2.1.3
IP 10.2.1.3 will be able to ping from R4 , but cannot ping from R3, R2, R1
This clearly shows problem at R4 since EIGRP is between DSW1, DSW2 & R4 and OSPF
protocol is running between R4, R3, R2, R1 so routes from R4 are not propagated to R3, R2, R1
Since R4 is able to ping 10.2.1.3 it means that routes are received in EIGRP & same needs to
be advertised in OSPF to ping from R3, R2, R1.
Need to check the routes are being advertised properly or not in OSPF & EIGRP vice-versa.
From above snap shot it clearly indicates that redistribution done in EIGRP is having problem &
by default all routes are denied from ospf to EIGRP… so need to change route-map name.
Change required:On R4, in redistribution of EIGRP routing protocol, we need to change name
of route-map to resolve the issue…
——————————————–
So in ticket Answer to the fault condition will be as below for:
The implementations group has been using the test bed to do a ‘proof-of-concept’ that
requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After
several changes to the network addressing, routing scheme, DHCP services, NTP services,
layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened
indicating that Client 1 cannot ping the 209.65.200.241 address.
Use the supported commands to isolated the cause of this fault and answer the following
questions.
On which device is the fault condition located?
A.
R1
B.
R2
C.
R3
D.
R4
E.
DSW1
F.
DSW2
G.
ASW1
H.
ASW2
Explanation: