The implementations group has been using the test bed to do a ‘proof-of-concept’ that requires
both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the
network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP
services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping
the 209.65.200.241 address.
Use the supported commands to isolated the cause of this fault and answer the following questions.
Which is the solution to the fault condition?
A.
Under the EIGRP process, delete the redistribute ospf 1 route-map OSPF_ to_ EIGRP command
and enter the redistribute ospf 1 route-map OSPF – > EIGRP command.
B.
Under the EIGRP process, delete the redistribute ospf 1 route-map OSPF_ to_ EIGRP command
and enter the redistribute ospf 6 metric route-map OSPF – > EIGRP command.
C.
Under the OSPF process, delete the redistribute eigrp10 subnets route-map EIGPR ->OSPF
command and enter the redistribute eigrp10 subnets route-map OSPF – > EIGRP command.
D.
Under the OSPF process, delete the redistribute eigrp10 subnets route-map EIGPR ->OSPF
command and enter the redistribute eigrp10 subnets route-map EIGPR – > OSPF command.
E.
Under the EIGRP process, delete the redistribute ospf 1 route-map OSPF _to_ EIGRP command and
enter redistribute ospf 1 metric 100000 100 100 1 15000 route_ map OSPF _to _EIGRP command
Explanation:
On R4, in the redistribution of EIGRP routing protocol, we need to change name of route-map to
resolve the issue. It references route-map OSPF_to_EIGRP but the actual route map is called OSPF-
>EIGRP.
===============================================================================
Ticket 9 : EIGRP AS number
Topology Overview (Actual Troubleshooting lab design is for below network design)
o Client Should have IP 10.2.1.3
o EIGRP 100 is running between switch DSW1 & DSW2
o OSPF (Process ID 1) is running between R1, R2, R3, R4
o Network of OSPF is redistributed in EIGRP
o BGP 65001 is configured on R1 with Webserver cloud AS 65002
o HSRP is running between DSW1 & DSW2 Switches
The company has created the test bed shown in the layer 2 and layer 3 topology exhibits.
This network consists of four routers, two layer 3 switches and two layer 2 switches.
In the IPv4 layer 3 topology, R1, R2, R3, and R4 are running OSPF with an OSPF process number 1.
DSW1, DSW2 and R4 are running EIGRP with an AS of 10. Redistribution is enabled where necessary.
R1 is running a BGP AS with a number of 65001. This AS has an eBGP connection to AS 65002 in the
ISP’s network. Because the company’s address space is in the private range.
R1 is also providing NAT translations between the inside (10.1.0.0/16 & 10.2.0.0/16) networks and
outside (209.65.0.0/24) network.ASW1 and ASW2 are layer 2 switches.
NTP is enabled on all devices with 209.65.200.226 serving as the master clock source.
The client workstations receive their IP address and default gateway via R4’s DHCP server.
The default gateway address of 10.2.1.254 is the IP address of HSRP group 10 which is running on
DSW1 and DSW2.
In the IPv6 layer 3 topology R1, R2, and R3 are running OSPFv3 with an OSPF process number 6.
DSW1, DSW2 and R4 are running RIPng process name RIP_ZONE.
The two IPv6 routing domains, OSPF 6 and RIPng are connected via GRE tunnel running over the
underlying IPv4 OSPF domain. Redistrution is enabled where necessary.
Recently the implementation group has been using the test bed to do a ‘proof-of-concept’ on several
implementations. This involved changing the configuration on one or more of the devices. You will
be presented with a series of trouble tickets related to issues introduced during these
configurations.
Note: Although trouble tickets have many similar fault indications, each ticket has its own issue and
solution.
Each ticket has 3 sub questions that need to be answered & topology remains same.
Question-1 Fault is found on which device,
Question-2 Fault condition is related to,
Question-3 What exact problem is seen & what needs to be done for solution
===============================================================================Client is unable to ping IP 209.65.200.241
Solution
Steps need to follow as below:-
1) When we check on client 1 & Client 2 desktop we are not receiving DHCP address from R4
ipconfig —– Client will be receiving IP address 10.2.1.3
2) From Client PC we can ping 10.2.1.254
3) But IP 10.2.1.3 is not able to ping from R4, R3, R2, R1
4) This clearly shows problem at R4 Kindly check routes in EIGRP there are no routes of eigrp.
5) Check the neighborship of EIGRP on R4; there are no neighbor seen from DSW1 & DSW2
check the running config of EIGRP protocol it shows EIGRP AS 1 process…. Now check on DSW1 & DSW2
On DSW1 only one Eigrp neighbour is there with DSW2 but its not with R4…1) From above snapshot & since R4 has EIGRP AS number 1 due to which neighbour is not
happening.
2) Change required: On R4, IPV4 EIGRP Routing, need to change the EIGRP AS number from 1
to 10 since DSW1 & DSW2 is configured to be in EIGRP AS number 10.
——————————————————————————————————————————
So in ticket Answer to the fault condition will be as below for