Which two statements about implementing Cisco NPV and NPIV on a Cisco Nexus 5000 Series switch are true?

Which two statements about implementing Cisco NPV and NPIV on a Cisco Nexus 5000 Series
switch are true? (Choose two.)

Which two statements about implementing Cisco NPV and NPIV on a Cisco Nexus 5000 Series
switch are true? (Choose two.)

A.
STP must run inside the FP network.

B.
All VLANs must be in the same mode, CE, or FP.

C.
FP port can join the private and nonprivate VLANs.

D.
Only F and M series modules can run FabricPath.

E.
These require an enhanced Layer 2 license to run.

Show Hint

Leave a Reply 4

Your email address will not be published. Required fields are marked *

Neumarkt opf

Neumarkt opf

The second answer is not just no sense

Reply

greenhorn

greenhorn

The answers and question do not fit. Question is about FCoE technology and answers are about FabricPath. Answers ACD are obviously wrong, so BE is the only option.

Reply

SHIVANNA

SHIVANNA

ATTENTION PLEASE!!!

The 642-997 Exam Has Retired, the New Exam is 300-165 Now!

New 300-165 Exam Questions and Answers Updated Recently (11/Oct/2017):

NEW QUESTION 177
You have a vPC configuration with two functional peers. The peer link is up and the peer-link feature is restricted the spanning-tree operations in the configuration? (Choose two.)

A. The primary and secondary switch generate and process BPDUs
B. vPC imposes a rules that the peer link is always blocking
C. vPC removes some VLANs from the spanning tree form the spanning tree for vPC use
D. vPC requires the peer link to remain in the forwarding states

Answer: AD

NEW QUESTION 178
You have a Cisco MDS switch that uses port channel. You must ensure that frames between the source and the destination follow the same links for a specific flow. Subsequent flows can use a different link, which load-balancing method do you use?

A. Source-destination-ip
B. Source-destioation-port
C. Flow
D. Source id-destination id-oxid

Answer: C

NEW QUESTION 179
Within the vPC configuration of the 7K’s, the command peer switch is configured. What is the result of enabling the command?

A. Both vPC peers use the same STP root ID.
B. The Vpc primary switch (7K-4 in this case) also serves as the STP root to improve vPC convergence.
C. The vPC secondary switch (7K-3 in this case) server as the STP root to improve vPC performance.
D. Allow 7K-3 to act as the active HSRP gateway for packets that are addressed to the MAC address of 7K-4.
E. Automatically disable IP redirects on all interface VLANs mapped over a vPC VLAN to avoid generation of IP redirect messages for packets switched though the vPC peer gateway router.
F. Enable faster convergence of ARP tables after the vPC peer link flaps.

Answer: B

NEW QUESTION 180
Refer to the following codes. Which result of the configuration snippet is true?
Vlan access-map map
Match mac address acl01
Action forward
Statistics per-entry
Vlan filter map vlan-list

A. A VACL map in applied to VLAN 101 and VLAN 200
B. VACL acl is applied to VLAN 100 through 200
C. Acl is applied to all of the VLANs on the switch
D. Global statistics are provided for the ACL map

Answer: A

NEW QUESTION 181
Refer to the following codes. You have a Cisco Nexus 7010 switch named N7k-1.
N7k-1# show runing-config fabricpath
……
Fabricpath switch-id 11
Vpc domain 11
Fabricpath switch-id 1100
Which command set should you run on a neighboring Cisco Nexus 7010 swith to estabish a vPC+ environment that includes N7k-1?

A. Fabricpath switch-id 11 Vpc domain 11 Fabricpath switch-id 1100
B. Fabricpath switch-id 12 Vpc domain 11 Fabricpath switch-id 1100
C. Fabricpath switch-id 12 Vpc domain 11 Fabricpath switch-id 1200
D. Fabricpath switch-id 11 Vpc domain 12 Fabricpath switch-id 1101

Answer: A

NEW QUESTION 182
Refer to the following codes. Which description of the output is true?
……

A. The default map-catch limit is used.
B. PETR is disable.
C. The table output apply to the default VRF.
D. The switch acts as an IPv4 LISP ETR.

Answer: B

NEW QUESTION 183
When configure HSPR on IPv6 enabled interface, which two configuration is correct?

A. switchA(config-if)?standbyt 6 preempt
B. switchA(config-if)?hsrp;
C. switchA(config-if)ff key 6
D. switchA(config-if)?hsrp version 2
E. switchA(config-if)B priority

Answer: B

NEW QUESTION 184
You have a Cisco FabricPath network. You must implement Vpc+ for a downstream switch. Which three actions should you preform? (Choose three.)

A. Configure the upstream switch to use PAgP in EtherChannel
B. Establish a peer link between the peer switch
C. Connect the downstream switch to a 10-Gb port
D. Configure a peer keep alive between the peer switches
E. Configure the switch ID on the peer switches
F. Configure the down switch to use PAgP on EtherChannel

Answer: BCD

NEW QUESTION 185
You have a Cisco Fabric Path network, you must extend the network to support more than 18 million segment, what should you do?

A. Enable the interface feature and configure the VLAN IDs.
B. Enable the nv overlay feature and configure the segment IDs.
C. Enable the vn-segment-vlan-based feature and configure segment IDs.
D. Enable the FabricPath feature and configure the VLAN IDs.

Answer: D

NEW QUESTION 186
……

P.S. These New 300-165 Exam Questions Were Just Updated From The Real 300-165 Exam, You Can Get The Newest 300-165 Dumps In PDF And VCE From — https://www.passleader.com/300-165.html (195q VCE and PDF)

Good Luck!

Reply