Which two statements are true about the primary address on an interface?

Which two statements are true about the primary address on an interface? (Choose two.)

Which two statements are true about the primary address on an interface? (Choose two.)

A.
By default, the primary address on an interface is selected as the numerically
highest local address configured on the interface.

B.
It can be useful for selecting the local address used for packets sent out of
unnumbered interfaces when multiple non-127 addresses are configured on the
loopback interface.

C.
It is the address used by default as the local address for broadcast and multicast
packets sourced locally and sent out of the interface.

D.
You use the primary address when you have multiple IP addresses belonging to
the same subnet on the same interface.

Show Hint

Leave a Reply 2

Your email address will not be published. Required fields are marked *

Todd Hatfield

Todd Hatfield

New JN0-102 Exam Questions (8/May/2017 Updated):

NEW QUESTION 361
Which keystroke combination allows users to move the cursor to the beginning of the command line without deleting text?

A. Ctrl + u
B. Ctrl + w
C. Ctrl + a
D. Ctrl + b

Answer: C

NEW QUESTION 362
What is the subnet mask for the 172.45.32.6/19 address?

A. 255.255.224.0
B. 255.255.240.0
C. 255.224.0.0
D. 255.240.0.0

Answer: A

NEW QUESTION 363
Click the Exhibit button. Referring to the exhibit, what happens when ping packets are sent to the management interface address of the local router?
user@router> show route protocol static
inet.0: 15 destinations, 15 routes (15 active, 0 holddown, 0 hidden)
+ = Active Route, – = Last Active, * = Both
99.0.0.0/17 *[Static/5] 00:00:11
————— > to 10.1.1.2 via ge-0/0/1.0
99.0.0.0/19 *[Static/5] 00:00:11
————— > to 10.1.2.2 via ge-0/0/2.0
99.0.0.0/24 *[Static/5] 00:00:11
————— > to 10.1.3.2 via ge-0/0/3.0
99.0.0.0/26 *[Static/5] 00:00:11
————— > to 10.1.4.2 via ge-0/0/4.0
Referring to the exhibit, which next-hop interface will be used to reach the 10.21.14.16 destination?

A. ge-0/0/1.0
B. ge-0/0/0.0
C. ge-0/0/3.0
D. ge-0/0/2.0

Answer: A

NEW QUESTION 364
What is the default firewall filter behavior when a term is matched but no terminating action is specified?

A. an implicit deny and the filter evaluation terminates
B. an implicit accept and the filter evaluation terminates
C. an implicit accept and the filter evaluation continues to the next term
D. an implicit deny and the filter evaluation continues to the next term

Answer: C

NEW QUESTION 365
What are three interface prefixes for a 40-gigabit interface? (Choose three.)

A. et
B. es
C. fte
D. xe
E. xle

Answer: ABE

NEW QUESTION 366
Which source of routing information is preferred by default?

A. static
B. RIP
C. direct
D. BGP

Answer: C

NEW QUESTION 367
For the interface ge-1/2/3.4, what does “ge” represent?

A. SONET/SDH
B. Gigabit Ethernet
C. Aggregated Ethernet
D. GRE

Answer: B

NEW QUESTION 368
Which word starts a command to display the operational status of a Junos device?

A. put
B. set
C. show
D. get

Answer: C

NEW QUESTION 369
……

And, Get The Newest JN0-102 Dumps In PDF And VCE From — http://www.passleader.com/jn0-102.html (408q VCE and PDF)

Good Luck!

Reply