— Exhibit — — Exhibit — Given the configuration shown in the exhibit, what will happen to
traffic from source 10.10.10.25 destined to 200.200.200.1?
A.
The traffic will be rejected.
B.
The traffic will be dropped.
C.
The traffic will be forwarded.
D.
The traffic will be policed.
Not sure about this one either. It would only meet the final term so it would be forwarded as there’s an implicit accept with out a terminating action – however it would also have the policer LAPD applied so you’d think it would be policed too.
When traffic meets term result and will be accepted , no other terms will be applied.
New JN0-102 Exam Questions Updated Recently (8/May/2017):
NEW QUESTION 358
Which two statements describe the default behavior for OSPF? (Choose two.)
A. OSPF imports all routes into the inet4.0 routing table.
B. OSPF exports all static routes into the OSPF database.
C. OSPF imports all routes into the inet.0 routing table.
D. OSPF does not export static routes into the OSPF database.
Answer: CD
NEW QUESTION 359
Which two ping command parameters whould be used to troubleshoot MTU issues? (Choose two.)
A. ping do-not-fragment
B. ping rapid
C. ping verbose
D. ping size
Answer: AD
NEW QUESTION 360
Which command prompt indicates that you are in operational mode?
A. user @ router &
B. user @ router #
C. user @ router $
D. user @ router >
Answer: D
NEW QUESTION 361
Which keystroke combination allows users to move the cursor to the beginning of the command line without deleting text?
A. Ctrl + u
B. Ctrl + w
C. Ctrl + a
D. Ctrl + b
Answer: C
NEW QUESTION 362
What is the subnet mask for the 172.45.32.6/19 address?
A. 255.255.224.0
B. 255.255.240.0
C. 255.224.0.0
D. 255.240.0.0
Answer: A
NEW QUESTION 363
Click the Exhibit button. Referring to the exhibit, what happens when ping packets are sent to the management interface address of the local router?
user@router> show route protocol static
inet.0: 15 destinations, 15 routes (15 active, 0 holddown, 0 hidden)
+ = Active Route, – = Last Active, * = Both
99.0.0.0/17 *[Static/5] 00:00:11
————— > to 10.1.1.2 via ge-0/0/1.0
99.0.0.0/19 *[Static/5] 00:00:11
————— > to 10.1.2.2 via ge-0/0/2.0
99.0.0.0/24 *[Static/5] 00:00:11
————— > to 10.1.3.2 via ge-0/0/3.0
99.0.0.0/26 *[Static/5] 00:00:11
————— > to 10.1.4.2 via ge-0/0/4.0
Referring to the exhibit, which next-hop interface will be used to reach the 10.21.14.16 destination?
A. ge-0/0/1.0
B. ge-0/0/0.0
C. ge-0/0/3.0
D. ge-0/0/2.0
Answer: A
NEW QUESTION 364
What is the default firewall filter behavior when a term is matched but no terminating action is specified?
A. an implicit deny and the filter evaluation terminates
B. an implicit accept and the filter evaluation terminates
C. an implicit accept and the filter evaluation continues to the next term
D. an implicit deny and the filter evaluation continues to the next term
Answer: C
NEW QUESTION 365
What are three interface prefixes for a 40-gigabit interface? (Choose three.)
A. et
B. es
C. fte
D. xe
E. xle
Answer: ABE
NEW QUESTION 366
Which source of routing information is preferred by default?
A. static
B. RIP
C. direct
D. BGP
Answer: C
NEW QUESTION 367
For the interface ge-1/2/3.4, what does “ge” represent?
A. SONET/SDH
B. Gigabit Ethernet
C. Aggregated Ethernet
D. GRE
Answer: B
NEW QUESTION 368
Which word starts a command to display the operational status of a Junos device?
A. put
B. set
C. show
D. get
Answer: C
NEW QUESTION 369
……
P.S. You Can Get The Newest JN0-102 Dumps In PDF And VCE From — http://www.passleader.com/jn0-102.html (408q VCE and PDF)
Good Luck!
BTW, part of that new 408Q JN0-102 dumps are available here:
https://drive.google.com/open?id=0B-ob6L_QjGLpSmYwaTA1elptOUE
Best Regards!
Just passed the JNCIA-Junos JN0-102 exam recently! Scored 90% (the passing line is 65%)!!
Though the JN0-102 test is Juniper’s entry-level certification, which is more difficult than the CISSP and CCNA exams. Hands-on Junos experience will help passing exam easily!!
I had 65 multiple-choice questionsin the actual test, most of them are NEW QUESTIONS, which are not available in those free JN0-102 dumps!
New questions FYI:
1. Which word starts a command to display the operational status of a Junos device?
2. For the interface ge-1/2/3.4, what does “ge” represent?
3. three interface prefixes for a 40-gigabit interface (et, es, xle).
4. command prompt indicates that you are in operational mode.
5. Exhibit — 10.21.14.16 destination — ge-0/0/1.0
…etc.
Questions on this site are sure not enough for passing, NEW QUESTIONS ARE NOT AVAILABLE!
Recommend you to learn the NEWEST & VALID PassLeader JN0-102 dumps here:
https://drive.google.com/open?id=0B-ob6L_QjGLpSmYwaTA1elptOUE
(IT IS THE NEWEST VERSION — 408 Q&As!!!)
Good Luck!!!
The connection faces term “result” and will be accepted and forwarded.
term results {
from {
address {
200.200.200.0/24;
}
}
then accept;