Which two commands would you use to view OSPF routes?

Which two commands would you use to view OSPF routes? (Choose two.)

Which two commands would you use to view OSPF routes? (Choose two.)

A.
show ip route ospf

B.
show ospf routes

C.
show route protocol ospf

D.
show route

Explanation:

Show Hint

Leave a Reply 6

Your email address will not be published. Required fields are marked *

jim

jim

B – too!!! check everybody!

Reply

jim

jim

Oh, no!
not B, because not simbol S at and.
Correctly it could be: >show ospf route

Reply

Gardener

Gardener

Just C and D. Practice on Olive.

Reply

humberto

humberto

show ospf route
show route protocol ospf
show route

Reply

Humberto

Humberto

New JN0-102 Exam Questions Updated Recently (8/May/2017):

NEW QUESTION 358
Which two statements describe the default behavior for OSPF? (Choose two.)

A. OSPF imports all routes into the inet4.0 routing table.
B. OSPF exports all static routes into the OSPF database.
C. OSPF imports all routes into the inet.0 routing table.
D. OSPF does not export static routes into the OSPF database.

Answer: CD

NEW QUESTION 359
Which two ping command parameters whould be used to troubleshoot MTU issues? (Choose two.)

A. ping do-not-fragment
B. ping rapid
C. ping verbose
D. ping size

Answer: AD

NEW QUESTION 360
Which command prompt indicates that you are in operational mode?

A. user @ router &
B. user @ router #
C. user @ router $
D. user @ router >

Answer: D

NEW QUESTION 361
Which keystroke combination allows users to move the cursor to the beginning of the command line without deleting text?

A. Ctrl + u
B. Ctrl + w
C. Ctrl + a
D. Ctrl + b

Answer: C

NEW QUESTION 362
What is the subnet mask for the 172.45.32.6/19 address?

A. 255.255.224.0
B. 255.255.240.0
C. 255.224.0.0
D. 255.240.0.0

Answer: A

NEW QUESTION 363
Click the Exhibit button. Referring to the exhibit, what happens when ping packets are sent to the management interface address of the local router?
user@router> show route protocol static
inet.0: 15 destinations, 15 routes (15 active, 0 holddown, 0 hidden)
+ = Active Route, – = Last Active, * = Both
99.0.0.0/17 *[Static/5] 00:00:11
————— > to 10.1.1.2 via ge-0/0/1.0
99.0.0.0/19 *[Static/5] 00:00:11
————— > to 10.1.2.2 via ge-0/0/2.0
99.0.0.0/24 *[Static/5] 00:00:11
————— > to 10.1.3.2 via ge-0/0/3.0
99.0.0.0/26 *[Static/5] 00:00:11
————— > to 10.1.4.2 via ge-0/0/4.0
Referring to the exhibit, which next-hop interface will be used to reach the 10.21.14.16 destination?

A. ge-0/0/1.0
B. ge-0/0/0.0
C. ge-0/0/3.0
D. ge-0/0/2.0

Answer: A

NEW QUESTION 364
What is the default firewall filter behavior when a term is matched but no terminating action is specified?

A. an implicit deny and the filter evaluation terminates
B. an implicit accept and the filter evaluation terminates
C. an implicit accept and the filter evaluation continues to the next term
D. an implicit deny and the filter evaluation continues to the next term

Answer: C

NEW QUESTION 365
What are three interface prefixes for a 40-gigabit interface? (Choose three.)

A. et
B. es
C. fte
D. xe
E. xle

Answer: ABE

NEW QUESTION 366
Which source of routing information is preferred by default?

A. static
B. RIP
C. direct
D. BGP

Answer: C

NEW QUESTION 367
For the interface ge-1/2/3.4, what does “ge” represent?

A. SONET/SDH
B. Gigabit Ethernet
C. Aggregated Ethernet
D. GRE

Answer: B

NEW QUESTION 368
Which word starts a command to display the operational status of a Junos device?

A. put
B. set
C. show
D. get

Answer: C

NEW QUESTION 369
……

P.S. These New JN0-102 Exam Questions Were Just Updated From The Real JN0-102 Exam, You Can Get The Newest JN0-102 Dumps In PDF And VCE From — http://www.passleader.com/jn0-102.html (408q VCE and PDF)

Good Luck!

Reply