— Exhibit — Click the Exhibit button. Referring to the exhibit, what is the shortest path from
R6 to R5?
A.
R6, R4, R2, R1, R3, R5
B.
R6, R5
C.
R6, R4, R2, R3, R5
D.
R6, R4, R5
what is the shortest path from R6 to R5?
— Exhibit — Click the Exhibit button. Referring to the exhibit, what is the shortest path from
R6 to R5?
D.
R6, R4, R5
C the metric is lower than option D
There is 9
B, It prefers intraarea than interarea
is this dump are valid????????
B.
R6, R5
The OSPF route selection rule is that intra-area routes are preferred over inter-area routes, which are preferred over external routes. However, this rule should apply to routes learned via the same process. In other words, there is no preference between external routes from one process compared to internal routes of other process.
ATTENTION PLEASE!!! The JNCIP-ENT JN0-643 exam has retired, and the new exam is JNCIP-ENT JN0-647 test now!!!
New JNCIP-ENT JN0-647 Exam Questions and Answers Updated Recently (15/Nov/2017):
NEW QUESTION 1
Your network provider supports multicast traffic but your provider network does not. You want to allow multicast hosts outside of your network to receive multicast traffic sourced within your network. How would you satisfy this requirement?
A. Use MSDP peering with your provider.
B. Use AutoVPN to connect to the remote hosts.
C. Use an MP-BGP session to your provider to pass multicast traffic.
D. Use automatic multicast tunnel gateway at the edge of your network.
Answer: D
NEW QUESTION 2
Which type of BGP is used to peer with a different autonomous system?
A. external
B. classless
C. dynamic
D. static
Answer: A
NEW QUESTION 3
Which protocol is used for port level access control and authentication?
A. MD5
B. IP sec
C. 802 IX
D. AES
Answer: C
NEW QUESTION 4
When configuring class of service, what would you use to allocate bandwidth to a forwarding class?
A. buffer depth
B. transmit rate
C. bandwidth
D. speed
Answer: B
NEW QUESTION 5
A packet enters the router and is subject to ingress’s processing. In which order is the packet processed?
A. policer > BA classifier > multifield classifier > forwarding policy
B. multifield classifier > BA classifier > policer > forwarding policy
C. BA classifier > multifield claasssifier > policer > forwarding policy
D. forwarding policy > BA classifier > multifield classifier > policer
Answer: C
NEW QUESTION 6
When configuring class of service, what would you use to allocate bandwidth to a forwarding class?
A. Buffer depth
B. Transmit rate
C. Bandwidth
D. Speed
NEW QUESTION 7
A new PoE+VoIP handset was added to an EX Series device. The handset is experiencing connectivity issues. The EX Series device’s committed configuration includes the set poe interface all telemetry command. You look at the telemetry log in the device to review power consumption and you notice entries have not been occurring for days. What would cause telemetry logging to stop?
A. Telemetry logging only occurs for one hour by default.
B. Telemetry logging stops when all reserves power for PoE has been consumed.
C. Telemetry logging only works on Enhanced PoE VoIP handsets.
D. Telemetry logging stops when the logging file reaches 128 KB.
Answer: A
NEW QUESTION 8
Which protocol is used for port-level access control and authentication?
A. MD5
B. IPsec
C. 802.1X
D. AES
Answer: C
NEW QUESTION 9
OSFP is stuck in the ExStart state. What is a common cause of this problem?
A. The DR priority is configured incorrectly.
B. MTUs do not match.
C. IP addresses are not configured correctly.
D. Jumbo frames are not enabled.
Answer: B
NEW QUESTION 10
Which three statements are true about strict-high priority queues? (Choose three.)
A. In systems that support strict-high and high priority queues, traffic in the strict-high queue is completely emptied, and then high priority queue traffic is processed.
B. In systems that support strict-high and high priority queues, traffic in these two priorities is processed in a round-robin fashion.
C. When a strict-high queue goes into negative credits, it will maintain a strict DSCP marking.
D. When a strict-high queue can never go into negative credits and will always transmit the traffic in the queue.
E. In systems that support multiple strict-high priority queues, traffic in the strict-high queue is processed in a round-robin fashion.
Answer: ADE
NEW QUESTION 11
Which two statements are true about 802.1Z dynamic filters based on RADUIS attributes? (Choose two.)
A. Filters can be defined on the network management system and deployed using vendor-specific attributes.
B. Filters can be defined on the switch and deployed upon authentication.
C. Filters can be defined on an automation framework and deployed when triggered by an authentication syslog message.
D. Filters can be defined on the authentication server and deployed using vendor-specific attributes.
Answer: BD
NEW QUESTION 12
You are configuring a scheduler map on an EX9200 Series device. You want to ensure that traffic is dropped in a policing action once traffic exceeds the configured transit rate. Which configuration parameter will meet this requirement?
A. exact
B. rate-limit
C. remainder
D. percent
Answer: B
NEW QUESTION 13
……
P.S. These New JN0-647 Exam Questions Were Just Updated From The Real JN0-647 Exam, You Can Get The Newest JN0-647 Dumps In PDF And VCE From — https://www.passleader.com/jn0-647.html (80q VCE and PDF)
Good Luck!
And, part of that new 80Q JN0-647 dumps FYI:
https://drive.google.com/open?id=0B-ob6L_QjGLpejBJUUI1X2NuU3M
Best Regards!