which action will solve this problem?

Click the exhibit button.
user@PE2# run show 12circuit connections
Layer-2 Circuit Connections:
Legend for connection status (St)
EI – – encapsulation invalid NP – – interface
h/w not present
MM – – mtu mismatch Dn – – down
EM – – encapsulation mismatch Vc-Dn – –
Virtual circuit Down
CM – – control-word mismatch UP – –
operational
VM – – vlan id mismatch CF – – Call admission
control failure
OL – – no outgoing label IB – – TDM
incompatible bitrate
NC – – intf encaps not CCC/TCC TM – – TDM
misconfiguration
BK – – Backup Connection ST – – Standby
Connection
CB – – rcvd cell-bundle size bad SP – – Static
Pseudowire
LD – – local site signaled down RS – – remote
sity standby
RD – – remote site signaled down HS – – Hotstandby Connection
XX – – unknown
Legend for interface status
UP – – operational
Dn – – down
Neighbor: 10.10.1.1
Interface Type St Time
last up #Up trans
ge-1/1/1.6 (vc 2) rmt VM
[edit protocols 12circuit]
user@PE2# show
neighbor 10.10.1.1. {
interface ge-1/1/1.6 {
virtual-circuit-id 2;
encapsulation-type ethernet-vlan;
}
}
[edit logical-systems jpe interfaces]
user@PE2# showge-1/1/1 {
unit 6 {
encapsulation vlan-ccc;
vlan-id 6;
family ccc;
}
}
user@PE1# run show 12circuit connections
logical-system kpe
Layer-2 Circuit Connections:
Legend for connection status (St)
EI – – encapsulation invalid NP – – interface
h/w not present
MM – – mtu mismatch Dn – – down
EM- – encapsulation mismatch VC-Dn – –
Virtual -circuit Down
CM – – control-word mismatch Up – –
operational
VM – – vlan id mismatch CF – – Call admission
control failure
OL – – no outgoing label IB – – TDM
incompatible bitrate
NC – – intf encaps not CCC/TCC TM – – TDM
misconfiguration
BK – – Backup connection ST – – Standby
Connection
CB – – rcvd cell-bundle size bad SP – – Static
Pseudowire
LD – – local site signaled down RS – – remote
site standby
RD – – remote site signaled down HS – – Hotstandby Connection
XX – – unknown
Legend for interface status
Up – – operational
Dn – – down
Neighbor: 10.10.1.3
Interface Type St Time
last up # Up trans
ge-1/0/1.5 (vc 2) rmt VM
[edit protocols 12circuit]
user@PE1# show
neighbor 10.11.1.1 {
interface ge-1/0/1.5 {
virtual-circuit-id 2;
encapsulation-type ethernet-vlan;
}
}
[edit interfaces]
user@PE1#
ge-1/0/1 (
unit 5 {
encapsulation vlan-ccc;
vlan-id 5;family ccc;
}
}
An LDP Layer 2 circuit between PE1 and PE2 is not passing traffic. Both PE1 and PE2 show the circuit state as
VM – – vlan id mismatch.
Referring to the exhibit, which action will solve this problem?

A.
Configure interfaces PE1:ge-1/0/1.5 and PE2:ge-1/1/1.6 with the output-vlan-map pop parameter.

B.
Configure interfaces PE1:ge-1/0/1.5 or PE2:ge-1/1/1.6 with the output-vlan-map swap parameter.

C.
Configure the LDP Layer 2 circuit with the no-control-word command on PE1 and PE2.

D.
Configure interfaces PE1:ge-1/0/1.5 and PE2:ge-1/1/1.6 with the output-vlan-map swap parameter.

Explanation:
The output-vlan-map swap parameter specifies the VLAN rewrite operation to replace a VLAN tag. The outer
VLAN tag of the frame is overwritten with the user-specified VLAN tag information. We do this on both
interfaces.
http://www.juniper.net/techpubs/en_US/junos15.1/topics/reference/configuration-statement/swapedit-interfaces.html