What are the default settings of the Cisco IMCCIMC NIC properties on a standalone Cisco UCS CSeries server?

What are the default settings of the Cisco IMCCIMC NIC properties on a standalone Cisco UCS CSeries server?

What are the default settings of the Cisco IMCCIMC NIC properties on a standalone Cisco UCS CSeries server?

A.
‘Shared LOM’ NIC mode with ‘Active-active’ NIC redundancy and DHCP enabled

B.
‘Shared LOM’ NIC mode with ‘Active-standby’ NIC redundancy and DHCP enabled

C.
‘Dedicated’ NIC mode with ‘Active-standby’ NIC redundancy DHCP disabled

D.
‘Dedicated’ NIC mode with ‘None’ NIC redundancy and DHCP enabled

F.
‘Cisco Card’ NIC mode with ‘Active-active’ NIC redundancy and DHCP enabled

Show Hint

Leave a Reply 6

Your email address will not be published. Required fields are marked *

Otto Bengtsson

Otto Bengtsson

New 642-999 Exam Questions and Answers Updated Recently (12/July/2016):

NEW QUESTION 144
Which three parameters can be configured for a vHBA? (Choose three.)

A. Enable persistent binding
B. Enable a hardware-based failover
C. Define a SAN pin group
D. Assign a QoS policy
E. Define an MTU
F. Assign a MAC address

Answer: ACD

NEW QUESTION 145
With Cisco UCS Manager, in which location do you monitor the chassis discovery process?

A. CMC
B. FSM
C. CDP
D. DME

Answer: B

NEW QUESTION 146
Which two protocols does the Cisco Integrated Management Controller support for managing standalone Cisco UCS -Series servers? (Choose two.)

A. SoL
B. IPMI
C. IPMIv2
D. SMASH CLP
E. SNMPv3

Answer: CE

NEW QUESTION 147
Which three statements about what occurs when a Cisco UCS -Series Blade Server connects to the SAN across a fabric interconnect that is enabled in Fibre Channel NPV mode are true? (Choose three.)

A. The server ports in F Port mode are pinned to the NP Ports
B. The E Ports are pinned to the E Ports on the fabric interconnect
C. Zoning is deployed on the fabric interconnect
D. The fabric interconnect is not assigned a Fibre Channel domain ID
E. Traffic that is received on the server ports in F Port mode from the server side is pinned to the NPIV-enabled uplink ports on the fabric interconnect
F. The fabric interconnect must have the Fibre Channel uplink port connected to the upstream switch F Port in NPIV mode that performs the Fibre Channel forwarder function

Answer: ADE

NEW QUESTION 148
You plan to implement FCoE on a Cisco UCS -Series server. Which option must you configure from the Cisco Integrated Management Controller GUI?

A. a vNIC failover
B. a boot table entry
C. NIV
D. FIP mode

Answer: D

NEW QUESTION 149
Refer to the exhibit. Which tables correctly map the HIF ports to active FEX NIF ports on a Cisco UCS 2208X IOM in discrete pinning mode?
Image URL: examgod.com/plimages/11644bd44ce2_10984/642-999-dumps-1491_thumb.jpg

A. Table 2 and Table 4
B. Table 1 and T able 4
C. Table 2 and Table 3
D. Table 1 and Table 2
E. Table 3 and Table 4

Answer: B

NEW QUESTION 150
You have a Cisco UCS C-Series Server. What can you use to log the blade server statistics?

A. the Cisco Integrated Management Controller log
B. RADIUS
C. LDAP
D. the XML API

Answer: A

NEW QUESTION 151
You manage Cisco UCS -Series Rack-Mount Servers. Which three components can you upgrade by using the Cisco Host Upgrade Utility? (Choose three.)

A. the LAN on motherboard
B. the Cisco Integrated Management Controller
C. the operating system images
D. the system BIOS
E. the fabric interconnects
F. the FEX modules

Answer: ABD

NEW QUESTION 152
Which three components are parts of the Cisco UCS -Series Blade Server software bundle? (Choose three.)

A. the adapter firmware
B. the Kernel and system firmware for fabric interconnects
C. the BIOS firmware
D. the IOM firmware
E. the Cisco UCS Manager software
F. the board controller firmware

Answer: ACF

NEW QUESTION 153
Which slot(s) contain DIMMs in a 1DPC configuration on Cisco UCS blade server?

A. 0
B. 1 and 2 only.
C. 1
D. 2

Answer: C

NEW QUESTION 154
Which destination(s) are valid for syslog messages for a Cisco UCS Fabric Interconnect?

A. a file and monitor only
B. the log, the monitor and syslog queue
C. the console
D. the console and log only
E. a file
F. the console, the monitor, and a file

Answer: F

NEW QUESTION 155
……

P.S. These New 642-999 Exam Questions Were Just Updated From The Real 642-999 Exam, You Can Get The Newest 642-999 Dumps In PDF And VCE From — http://bit.ly/642-999-dumps-vce-pdf (175q)

Good Luck !!!

Reply

TB

TB

Correct answer is A:

The server is shipped with these default settings:

The NIC mode is Shared LOM EXT.

Shared LOM EXT mode enables the 1-Gb Ethernet ports and the ports on any installed Cisco virtual interface card (VIC) to access Cisco Integrated Management Interface (Cisco IMC). If you want to use the 10/100/1000 dedicated management ports to access Cisco IMC, you can connect to the server and change the NIC mode as described in Step 1 of the following procedure.

The NIC redundancy is active-active. All Ethernet ports are utilized simultaneously.
DHCP is enabled.
IPv4 is enabled. You can change this to IPv6.

http://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/c/hw/C240M4/install/C240M4/install.html#46057

Reply

Dieter Mauler

Dieter Mauler

New 642-999 Exam Questions Updated Recently (29/June/2017):

NEW QUESTION 177
Which two statements describe effects of enabling a Cisco UCS Fabric Interconnect in Ethernet end-host mode? (Choose two.)

A. MAC address learning is disabled on the uplink ports of the fabric interconnect.
B. MAC address learning is enabled on the server ports of the fabric interconnect.
C. Server-to-server communication on the same VLAN is not performed locally VIE Fabric Interconnect, but requires an external switch.
D. By default, unicast traffic received by the fabric uplink port to unknown destination MAC addresses is forwarded to all of the server ports.
E. MAC address learning is disabled on all of the ports in Ethernet end-host mode.

Answer: BC

NEW QUESTION 178
Which parameter can be configured during the initial system setup of Cisco UCS Fabric Interconnect from the CLI, without restoring the configuration from an existing backup?

A. the server ports, network ports, and storage ports
B. the reserved VLAN IDs
C. the default number of dynamic vNICs
D. standalone mode or cluster mode of the Fabric Interconnects

Answer: D

NEW QUESTION 179
Which two parameters must be configured on a standalone Cisco UCS C-Series Server to export the technical support data to a remote server? (Choose two.)

A. Specify a remote TFTP server IP address
B. Install a certificate
C. Install an FTP server
D. Set the source as the UCS server IP address
E. Specify the remote relative path and file name

Answer: AE

NEW QUESTION 180
……

NEW QUESTION 181
A Cisco UCS administrator configuring QoS, which two options are valid QoS system classes in a Cisco UCS blade system? (Choose two.)

A. drop eligible
B. transactaional data
C. best effort
D. scavenger
E. Fibre Channel

Answer: CE

NEW QUESTION 182
Which options is the only supported link aggregation protocol on Cisco UCS Manager?

A. Multipath
B. PagP
C. FLOGI
D. LACP
E. FCOE

Answer: D

NEW QUESTION 183
……

NEW QUESTION 184
Which drive combination prevents you from provisioning RAID on Cisco UCS C-Series servers?

A. SAS HDD and SATA HDD
B. SAS SSD and SATA SSD
C. SATA HDD and SATA SSD
D. SAS HDD only
E. SATA HDD only

Answer: C

NEW QUESTION 185
……

NEW QUESTION 186
Which two AAA protocols are supported by a remote AAA database? (Choose two.)

A. Microsoft Active Directory
B. RADIUS
C. 802.1X
D. Kerberos
E. LDAP

Answer: BE

NEW QUESTION 187
……

P.S. These New 642-999 Exam Questions Were Just Updated From The Real 642-999 Exam, You Can Get The Newest 642-999 Dumps In PDF And VCE From — http://www.passleader.com/642-999.html (195q VCE and PDF)

Good Luck!

Reply