which two fields are required to successfully create a …

Of the fields listed, which two fields are required to successfully create a phone user in Cisco
Unified Communications Manager? (Choose two.)

Of the fields listed, which two fields are required to successfully create a phone user in Cisco
Unified Communications Manager? (Choose two.)

A.
Last Name

B.
PIN (and confirmation PIN)

C.
Primary Extension

D.
User ID



Leave a Reply 1

Your email address will not be published. Required fields are marked *


Ramon109109

Ramon109109

QUESTION
Which Cisco Unified Communications Manager device report provides key information to determine if an additional gateway is needed?

A. Gateway utilization
B. Gateway summary
C. Gateway detail
D. Gateway and line group utilization

Answer: A

QUESTION
Which four tasks does RTMT allow an administrator to perform? (Choose four.)

A. View syslog messages.
B. Generate alerts when threshold is below or above user-configured.
C. Monitor a set of predefined management objects that monitor the health of the system.
D. Collect information and traces about errors or alerts that exist in the RTMT.
E. Reboot the system.
F. Perform incremental backups.
G. Export CDR.

Answer: ABCD

QUESTION
Which server does Cisco recommend that you configure before a CUCM backup?

A. SFTP
B. FTP
C. SNMP
D. TFTP

Answer: A

QUESTION
What is the interface type that you should use to connect a PSTN analog line to the VoIP network?

A. FXS
B. FXO
C. E and M
D. Serial

Answer: B

QUESTION
Which command is used to troubleshoot calls as they enter and leave a PRI connection?

A. Debug isdn q 931
B. Show voice call summary
C. Debug voip dialpeer
D. Show dial-peer voice summary

Answer: A

QUESTION
Which configuration causes PSTN users to experience a fail tone for every other call when trying to reach a particular number on Cisco Unified CME?

A. ephone-dn is not assigned to the ephone.
B. Duplicate ephone-dn is not assigned to the ephone.
C. ephone is not registered.
D. ephone does not exist for the ephone-dn.

Answer: B

QUESTION
Which Cisco Unified Communications Manager configuration causes an IP phone screen to display a “registration rejected” message?

A. Cisco Unified Communications Manager is unable to reach user IP phone.
B. Cisco Unified Communications Manager database replication status is 2.
C. Cisco Unified Communications Manager auto registration is disabled.
D. Cisco Unified Communications Manager is unable to allocate DN.
E. Cisco Unified Communications Manager subscriber is offline.

Answer: D

QUESTION
Customer requirements dictate that local calls from area code 408 display the ANI as a 7-digit number.
Which procedure allows the leading digits to be stripped as soon as they arrive at the H.323 voice gateway?

A. Set up a voice translation rule, apply the translation rule to a translation profile, and apply
the translation profile to the dial peer in the inbound direction.
B. Set up a voice translation profile, apply the translation profile to a translation rule, and apply
the translation rule to the dial peer in the outbound direction.
C. Set up a voice translation rule, apply the translation rule to a translation profile, and apply
the translation profile to the dial peer in the outbound direction.
D. Set up a voice translation profile, apply the translation profile to a translation rule, and apply
the translation rule to the dial peer in the inbound direction.

Answer: A

QUESTION
An end user has made more attempts to log in than allowed, using the wrong voice-mail pin.
The user has been locked out.
Which submenu does an administrator select to unlock the pin?

A. Change password
B. Password settings
C. Message settings
D. Mailbox

Answer: B

QUESTION
Which three methods can remotely force a Cisco Unified Communications Manager Express phone to reset? (Choose three.)

A. Issue a shutdown, no shutdown command on a switch port that provides PoE to a Cisco
phone.
B. Issue the restart command under the ephone-dn configuration of the phone.
C. Issue the reset command under the ephone configuration of the phone.
D. Issue the reset command under the ephone-dn configuration of the phone.
E. Issue the reset H.H.H (mac-address) command telephony-service configuration.
F. Issue the reset H.H.H (mac-address) command under global configuration.

Answer: ACE

More: https://www.braindump2go.com/210-065.html