You want to configure Port A on a Cisco TelePresence MCU 5300 with IP address 192.168.1.43, subnet mask
255.255.255.0, and default gateway 192.168.1.1.
Which of the following commands or command sets should you issue? (Select the best answer.)
A.
static A 192.168.1.43 255.255.255.0 192.168.1.1
B.
ip address 192.168.1.43 255.255.255.0 192.168.1.1
C.
set network ip static 192.168.1.43 255.255.255.0 192.168.1.1
D.
xConfiguration Network 1 IPv4 Address: “192.168.1.43”
xConfiguration Network 1 IPv4 SubnetMask: “255.255.255.0”
xConfiguration Network 1 IPv4 Gateway: “192.168.1.1”
E.
interface A
ip address 192.168.1.43 255.255.255.0
ip defaultgateway 192.168.1.1
Explanation:
You should issue the static A 192.168.1.43 255.255.255.0 192.168.1.1 command. The static command
configures a static IP address for a port on the Cisco TelePresence multipoint control unit (MCU) 5300. The
syntax of the static A command is static Aipaddresssubnetmask [defaultgateway].
The Cisco MCU 5300 has two Ethernet interfaces: Port A and Port B. To configure Port B with a static IP
address, you should issue the static B ipaddresssubnetmask [defaultgateway] command.
You can also configure a static IP address for either port by using the web interface. To do so, navigate toNetwork > Port A or Network > Port B, set the IP configurationoption to Manual, and configure the IP address,
Subnet mask, and Default gatewayfields.
You should not issue the following command set:
interface A
ip address 192.168.1.43 255.255.255.0
ip defaultgateway 192.168.1.1
This command set is similar to the IP address configuration of a Cisco router or switch. However, these
commands are not valid on a Cisco MCU 5300.
You should not issue the ip address 192.168.1.43 255.255.255.0 192.168.1.1command. The ip address
command is not valid on a Cisco MCU 5300.
You should not issue the following command set:
xConfiguration Network 1 IPv4 Address: “192.168.1.43”
xConfiguration Network 1 IPv4 SubnetMask: “255.255.255.0”
xConfiguration Network 1 IPv4 Gateway: “192.168.1.1”
You would issue these commands to configure a static IP address on a Cisco TelePresence System (CTS)
Codec, such as the C40 or C60.
You should not issue the set network ip static 192.168.1.43 255.255.255.0 192.168.1.1 command. The set
network ip static command is used to configure a static IP address on a CTS 1000. The syntax of the set
network ip static command is set network ip static ipaddress subnetmask defaultgateway [dnsaddress1]
[dnsaddress2] [domain]. After you configure the static IP address, the CTS 1000 will automatically restart.https://www.cisco.com/c/dam/en/us/td/docs/telepresence/infrastructure/mcu/install_guide/
Cisco_TelePresence_MCU_53x0_Installation_Guide.pdf#page=6
Got some new questions:
QUESTION
A group of managers for a company has requested IP telephony reports with performance data and graphs. Which steps should the network administrator take to gather these reports using Cisco Unified Communications Manager web interface?
A. Select Cisco Unified Serviceability > Trace > Serviceability Reports Archives.
B. Select Cisco Unified Serviceability > Alarm > Serviceability Reports Archives.
C. Select Cisco Unified Reports > Tools > Serviceability Reports Archives.
D. Select Cisco Unified Reports > Trace > Serviceability Reports Archives.
E. Select Cisco Unified Serviceability > Tools > Serviceability Reports Archives.
Answer: E
QUESTION
An engineer is configuring the Cisco Unified Communications Manager disaster recovery system. Which three statements about the disaster recovery system are true? (Choose three.)
A. It requires the use of schedules for backups.
B. Backup files are encrypted using the cluster security password.
C. If the backup device is listed in a backup schedule, it cannot be manually deleted.
D. If the backup does not complete within 40 hours, the backup times out.
E. Archiving backups to tape drives is supported.
F. SSL is used between the master and local agents.
Answer: BCE
QUESTION
An administrator wants to verify that a new PRI is properly connected to the PSTN status.
Which Layer 2 status should be seen?
A. MULTIPLE_FRAME_ESTABLISHED
B. TEI_ASSIGNED
C. LINK_UP
D. CONTROLLER_UP
Answer: A
QUESTION
After getting reports that users cannot make calls out to the PSTN, a network administrator opens the Cisco Unified Communications Manager Administration web page and begins to review route patterns. Why would the administrator look here when troubleshooting PSTN connectivity troubles?
A. A route pattern contains a list of gateways that can reach the PSTN.
B. A route pattern contains dial plan information for calling the PSTN.
C. A route pattern contains the necessary privileges for calling the PSTN.
D. A route pattern contains a list of SIP trunks that can reach the PSTN.
Answer: B
QUESTION
A user reports that several IP phones in a single department are displaying a continuous “registering” message. Which fault domain should be investigated?
A. network router
B. Cisco Unified Communications Manager subscriber node
C. network switch
D. IP phones
E. SIP gateway
Answer: C
QUESTION
An end user reports that conference calls are failing. Which fault domain should be investigated first?
A. IP phone
B. Cisco Unified Communications Manager Media Resources
C. voice gateways
D. network routers and switches
Answer: B
QUESTION
An engineer receives an isolated report that the customer can make calls successfully from an IP phone to other IP phones, but receives an error recording when attempting to call someone over the PSTN. The user cannot recall the error recording to provide the specific error message. Which two steps should the network engineer take to begin troubleshooting? (Choose two.)
A. Enable debug isdn q931 on the gateway and have user make the same call from the IP phone to PSTN again.
B. Check the region used by the IP phone in Cisco Unified Communications Manager.
C. Test the call using Dialed Number Analyzer in Cisco Unified Communications Manager administrator.
D. Check the calling search space used by the line on the IP phone in Cisco Unified Communications Manager.
E. Check the gateway to determine which codec is being used by the appropriate dial peer.
Answer: CD
QUESTION
A technician is checking services in response to the recent failed delivery of all voicemails. Which service must be running for message delivery to function properly?
A. Connection DB Event Publisher
B. Connection Database Proxy
C. Connection Notifier
D. Connection Message Transfer Agent
Answer: D
QUESTION
A field technician must reset a single 7965 IP phone so that it will be discovered on the network again and request an IP address from DCHP. Which steps should the network engineer provide?
A. Have field technician select the Settings button on phone, then dial # # * * *
B. Have field technician select the Settings button on phone, then dial # # * # #
C. Have field technician select the Settings button on phone, then dial * * # * *
D. Have field technician select the Settings button on phone, then dial * * # # #
Answer: C
QUESTION
An end user is experiencing performance issues with their IP phone. Which phone feature could the administrator configure to allow the end user to notify them when issues occur?
A. Cisco Quality Report Tool
B. System Log Management
C. Cisco CDR Analysis and Reporting
D. Cisco JTAPI
Answer: A
QUESTION
An end user has an 7945 IP phone, but is unable to launch any of the IP phone applications.
A network engineer has confirmed that the device is subscribed to the appropriate applications in Cisco Unified Communications Manager.
How should the engineer instruct the user to launch the IP phone applications?
A. Select the “?” button on the IP phone.
B. Select the globe button on the IP phone.
C. Select Settings > User Preferences.
D. Select Settings > Device Configuration.
Answer: B
210-060 real exam questions full version can be viewed here: https://www.braindump2go.com/210-060.html